Go to Post Eh, typical FIRST team, take something awesome and make it even better. - rsisk [more]
Home
Go Back   Chief Delphi > Technical > Technical Discussion
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
 
 
Thread Tools Rate Thread Display Modes
Prev Previous Post   Next Post Next
  #31   Spotlight this post!  
Unread 10-05-2016, 07:55
Gdeaver Gdeaver is offline
Registered User
FRC #1640
Team Role: Mentor
 
Join Date: Mar 2004
Rookie Year: 2001
Location: West Chester, Pa.
Posts: 1,357
Gdeaver has a reputation beyond reputeGdeaver has a reputation beyond reputeGdeaver has a reputation beyond reputeGdeaver has a reputation beyond reputeGdeaver has a reputation beyond reputeGdeaver has a reputation beyond reputeGdeaver has a reputation beyond reputeGdeaver has a reputation beyond reputeGdeaver has a reputation beyond reputeGdeaver has a reputation beyond reputeGdeaver has a reputation beyond repute
Re: Waterjet vs. Manual Build Process?

We used a 500mm X-carve this past season. Yes, it can cut aluminum. However, it is not the same as a high end industrial router. The X-carve is fine on softer materials. It is based on extrusions and v wheels. There are some modifications that must be made to increase the stiffness. The x carriage is 2 40 x 20 rails with a 4mm gap between them. Look on the X-carve forum for suggestions on stiffening the x axis. The y also needs stiffening on the larger machine. Use good end mills that are coated and designed for AL. 45 degree helix is good for chip clearance. It take time and effort to square the machine and calibrate it. If this done right the X carve can give precise cuts. You will have to go slow. Chip clearance is a must. A couple of re-cut chips will lead to an exercise in friction welding. The X-carve can not " hog" out Aluminum.If you want to "hog" out Aluminum then you need a 6000$ plus machine. 6061-T6 is not to bad. This year with the stress of our catapult 6061 plates failed from shock loads. We got a 4 x 4' x .125" sheet of 7075 from a salvage yard. We cut many parts from it. The X-carve was pushed to the limit on it. .003" depth of cut and 10" per minute travel on an 1/8" mill. The cuts were precise and the 7075 did not fail. One reason I like the 500 X-carve is that it is portable. We do not have the space for a permanent location. I take it to meetings and bring it home. I used an Arduino uno r3 and a Protoneer shield. DRV8825 driver chips. I have had to replace some driver chips. When the driver chips fail it took out the arduino. With this set up I was out 23 bucks as compared to 100$ plus for other boards. Blow lots of air on the driver chips. So yes the X-carve can cut AL but it can not hog out AL. This summer The X-carve is being rebult and modified to give a larger cut area and increased stiffness to allow faster cutting next year. One more thing. Software is important. The cam software should use helical bores, ramps and v-tabs and peck drills. Plunging is not good for the x-carve.
Reply With Quote
 


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 23:48.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi