Off season T-Shirt Launching Tank Robot

[juju_beans]

Almost done!

Here's a short video of our shooting test on the robot. Still have to get some code on the robot to run it. The turret is also on backwards but we're too lazy to run some code to turn it around haha.

https://www.youtube.com/watch?v=vC1d51Z6fuY

Now we just have to finish the pneumatics, loading mechanism, 3D print a ton of wheels, and finish the drive train.

Some more pictures: https://imgur.com/a/iF3vY

[cbale2000]

Originally Posted by juju_beans

Almost done!

Here's a short video of our shooting test on the robot. Still have to get some code on the robot to run it. The turret is also on backwards but we're too lazy to run some code to turn it around haha.

https://www.youtube.com/watch?v=vC1d51Z6fuY

Now we just have to finish the pneumatics, loading mechanism, 3D print a ton of wheels, and finish the drive train.

Some more pictures: https://imgur.com/a/iF3vY

Two questions:

1. What type of storage tank are you using for your accumulator, what pressure does it operate at, and where did you get it from?
2. What type of hose are you using between the accumulator and the cannon?

It's looking great so far, can't wait to see the finished product!

[nirmatt_1690]

Originally Posted by juju_beans

Almost done!

Here's a short video of our shooting test on the robot. Still have to get some code on the robot to run it. The turret is also on backwards but we're too lazy to run some code to turn it around haha.

https://www.youtube.com/watch?v=vC1d51Z6fuY

Now we just have to finish the pneumatics, loading mechanism, 3D print a ton of wheels, and finish the drive train.

Some more pictures: https://imgur.com/a/iF3vY

looking great!
what is the max firing rate?

[juju_beans]

Originally Posted by cbale2000

Two questions:

1. What type of storage tank are you using for your accumulator, what pressure does it operate at, and where did you get it from?
2. What type of hose are you using between the accumulator and the cannon?

It's looking great so far, can't wait to see the finished product!

1. The shooting tank is a metal storage tank that operates at anywhere from about 70 psi if we're low on air to 110 when we're full on air. It is rated of 220 psi I think. The big black tank is just another metal tank that holds 120 psi and slowly feeds into the shooting tank. Not actually sure where we got either from sorry!

2. 3/4 inch pvc hose. It is rated for up to 120 I'm pretty sure.

Originally Posted by nirmatt_1690

looking great!
what is the max firing rate?

Right now the magazine isn't done so we don't really know the firing rate, but it should be fairly fast as after it shoots it just unlocks the shell, ejects the shell, then lets the next shell fall down and finally seals the shell and it is ready to shoot.

[Mk.32]

Originally Posted by juju_beans

1. The shooting tank is a metal storage tank that operates at anywhere from about 70 psi if we're low on air to 110 when we're full on air. It is rated of 220 psi I think. The big black tank is just another metal tank that holds 120 psi and slowly feeds into the shooting tank. Not actually sure where we got either from sorry!

2. 3/4 inch pvc hose. It is rated for up to 120 I'm pretty sure.



Right now the magazine isn't done so we don't really know the firing rate, but it should be fairly fast as after it shoots it just unlocks the shell, ejects the shell, then lets the next shell fall down and finally seals the shell and it is ready to shoot.

As an Ex-3647 student... i remember that tank...

The smaller grey tank was obtained from McMaster-Carr and is stupidly heavy/overbuilt for FRC competition uses (like 300+ PSI).

The bigger black one looks like it's an off-road compressor tank used by off-roaders for air reserves. IE http://www.walmart.com/ip/42279947?w...590128&veh=sem

We have used the later on 2485 to good success.

[cbale2000]

Originally Posted by Mk.32

As an Ex-3647 student... i remember that tank...

The smaller grey tank was obtained from McMaster-Carr and is stupidly heavy/overbuilt for FRC competition uses (like 300+ PSI).

The smaller tank was the one I was interested in because of the large output port, almost every other tank I've found has much smaller (1/8" typically) ports which makes adapting to a 1" sprinkler valve (or non-plastic functional equivalent) much harder.

EDIT: Is this similar to what you have? http://www.mcmaster.com/#9908K19