General Pneumatic Advice and Help

[Ogehsim]

I'm mentoring our electrical/pneumatic group this year with no prior pneumatic experience. What would you say are some of the most common mistakes? If there's anything to watch out for so we don't have to route the tubing twice, what should we make sure to quadruple check?

The warnings/advice I've gotten so far are 1. cut the tube square and 2. teflon tape your connections prior to stuffing the tubing on.

[Wren Hensgen]

Originally Posted by Ogehsim

The warnings/advice I've gotten so far are 1. cut the tube square and 2. teflon tape your connections prior to stuffing the tubing on.

Good morning!

I absolutely agree with point 1. It's THE most common mistake. Cut it square and neat, and don't reuse ends after you insert them. Buy a tubing cutter, they're cheap, simple, and accurate.

For point 2, I really hope you mean taping the threads of the fitting. You should never, ever tape the tube itself. You'll foul the fitting, and send little bits of teflon tape through your air system.

Teflon tape is a bit of a polarizing question. If you do it right, it's fast, easy, and clean. However, if you don't, you can reduce airflow, CREATE leaks, and foul your tubing. Instead, I'd suggest a sealant. Similar to loctite, you drip a little onto the threads, and snug them down. Permatex is the brand I'd suggest. It's a lovely purple color.

On the subject of tightening fittings, be careful. Never use an adjustable wrench. Most air fittings are brass, or softer metal, and you just strip them out. Use a correct wrench, and just snug them down. You'll never get them all the way to the bottom because the threads widen (NPT), and are intended to jam.

I'd also be careful mounting your air tanks. Don't use hose clamps. Make a bracket, or use plastic plumber's tape. Hose clamps will cause the tank to fail.

The other tip that few people know is that some fittings (Norgren, SMC, and a few others) have an INTERNAL hex. You can put an allen key inside the fitting, and snug it down that way, which is a lifesaver in tight spots.

[pchild]

Originally Posted by Wren Hensgen

Good morning!

The other tip that few people know is that some fittings (Norgren, SMC, and a few others) have an INTERNAL hex. You can put an allen key inside the fitting, and snug it down that way, which is a lifesaver in tight spots.

I just wanted to thank you for posting this, I checked on the fittings we use and they do have internal hex. We've used pneumatics for years and somehow no one on our team has caught this! We've been tightening fittings onto our solenoids incorrectly for years!

[Wren Hensgen]

Originally Posted by pchild

I just wanted to thank you for posting this, I checked on the fittings we use and they do have internal hex. We've used pneumatics for years and somehow no one on our team has caught this! We've been tightening fittings onto our solenoids incorrectly for years!

Not all fittings have these, but they're so convenient to have! I'd suggest always buying Norgren fittings if possible, they're the only brand that consistently broaches the inside. IIRC, they have the original patent on doing so.

[ToddF]

Wren,
Theoretical question: Given that the sealing surface of a push to connect fitting is the OD of the tube, well away from the end, why is the end of tube geometry critical to the sealing of the fitting? In other words, WHY does the end of the tube need to be perfectly square to seal properly?

[Wren Hensgen]

Originally Posted by ToddF

Wren,
Theoretical question: Given that the sealing surface of a push to connect fitting is the OD of the tube, well away from the end, why is the end of tube geometry critical to the sealing of the fitting? In other words, WHY does the end of the tube need to be perfectly square to seal properly?

Good question! I've not seen that particular diagram before, but it does give you a bit of the wrong idea.

The seal isn't accomplished along a length of the tube, but instead at a very narrow band right near the end. If the tube isn't square, it may not sit entirely inside the band. The smaller and more compact the fitting, the narrower the sealing band is, and the more critical the square.

The other reason you want tubes to end square is the same reason that you cut stranded wires flush, instead of leaving whiskers. The gripper ring can be fouled by small slivers of tube that stick out, or they can impede airflow inside a fitting itself.

[GeeTwo]

Originally Posted by ToddF

Wren,
Theoretical question: Given that the sealing surface of a push to connect fitting is the OD of the tube, well away from the end, why is the end of tube geometry critical to the sealing of the fitting? In other words, WHY does the end of the tube need to be perfectly square to seal properly?

Speculation: When you push a beveled-end tube in all the way, it induces a torque on the tube, pulling the OD of the tube away from the ID of the fitting on that side.

[JamesCH95]

Aside from the nit below, great post!

Originally Posted by ToddF

Wren,
Theoretical question: Given that the sealing surface of a push to connect fitting is the OD of the tube, well away from the end, why is the end of tube geometry critical to the sealing of the fitting? In other words, WHY does the end of the tube need to be perfectly square to seal properly?

I like this diagram to explain how the fittings work:



The packing seals against the outside of the tube near the end. It is quite possible to cut the end of the tube at an angle and achieve a sealed joint. I have personally run this experiment to satisfy my own curiosity.

However, I strongly agree that tubes should be cut with a tubing cutter only. It is an inexpensive and easy way to make sure the tubing is cut without burrs or excessive deformation. Tubing that gets mashed flat with wire cutters doesn't seal well...

[Wren Hensgen]

Originally Posted by JamesCH95

Aside from the nit below, great post!

Thank you! There seems to always be surprisingly little general knowledge about air systems, especially the where/why/which of using them in FIRST.

Originally Posted by JamesCH95

Tubing that gets mashed flat with wire cutters doesn't seal well...

I've watched several teams cut their tubing with a dull knife, while just sorta vaguely holding it. Then they're surprised when it leaks. It's much easier just to say "Always cut tubing square with this tool".

That's also a much better diagram, thanks for the better explanation.

[Ogehsim]

Originally Posted by Wren Hensgen

For point 2, I really hope you mean taping the threads of the fitting. You should never, ever tape the tube itself. You'll foul the fitting, and send little bits of teflon tape through your air system.

Teflon tape is a bit of a polarizing question. If you do it right, it's fast, easy, and clean. However, if you don't, you can reduce airflow, CREATE leaks, and foul your tubing.

Thanks! I did mean taping the threads of the fitting. I'm still getting a hang of all the vocab.

I like the idea of the Permatex. However, out of curiosity, what is the right way to do Teflon tape?

[Wren Hensgen]

Originally Posted by Ogehsim

I like the idea of the Permatex. However, out of curiosity, what is the right way to do Teflon tape?

Three tight wraps, with the narrowest tape you can find. Start at least two threads up from the bottom. Wrap in the same direction as the fitting will be screwed in, so that tightening the fitting doesn't just strip the tape off.

The sealant I've had good experiences with is linked below.

https://www.permatex.com/products/th...aulic-sealant/