|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
| Thread Tools | Rate Thread | Display Modes |
|
#136
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
The 4-40 is 1.125" McMaster part # 91864A029. Box 0f 10, $6.47.
As an FYI, the Cylinder is McMaster #4208K102. The screw to insert into the shaft is McMaster #92311A197, box of 100. |
|
#137
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
Ta!
|
|
#138
|
|||
|
|||
|
Re: WCP: 2017 Product Launch + MCC 2017
Quote:
......... This was a request for help. If you actually read the thread you'll find a few more people having issues. I suspect there are many more afraid to post here since CD is so quick to shame anyone who has negative experience and posts about it. |
|
#139
|
|||
|
|||
|
Re: WCP: 2017 Product Launch + MCC 2017
Quote:
Also, if you enter your information in your CD profile, you can PM RC as well. Adding your team info can also help others help you with parts you might need, that's why it is important to include. You made that weird implicit connection yourself about being a competitor. -Akash Last edited by Akash Rastogi : 08-02-2017 at 13:08. |
|
#140
|
|||||
|
|||||
|
Re: WCP: 2017 Product Launch + MCC 2017
Quote:
I get on average 30-50 emails daily during the build season. I'm going to be frank and have not seen your email. If you could please resend with the header CD - Cylectron and I'll get back to you. Also you can PM me via CD as well. Thanks! |
|
#141
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
R.C.
Now that we (finally) have all of those dog gears for the DS Flipped transmissions, when can we order more? What kind of time frame are we looking at? I didn't think we would have enough money this year to build a practice bot, so we only ordered 2, but that ended up not being the case. Unfortunately, we were not aware of this until after you put them "Out Of Stock". What parts are currently unavailable? Also, we were able to get a local source/sponsor for the pancake cylinders, so we ordered them using the part number in your build instructions. When they came in, they were the square ones, which don't match the mounting holes in the plates--apparently, we need the round cylinders. Can you verify that the part number in the instructions is correct, and if not, could you change it for future users so we get the right cylinder? BTW, the quality and construction are really top-notch!! |
|
#142
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
Quote:
Check my post above (#136), it has all the part numbers needed for the correct cylinders, shaft screws and mounting screws. We ran into this issue a week ago. RC gave us the corrected info. With overnight from McMaster we are all set now. BTW, you are right about the build quality! |
|
#143
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
Any modification of pneumatic components is illegal. That includes any drilling of pre-existing holes on the cylinder.
|
|
#144
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
It's not on the cylinder that we drilled and tapped, it's on a piece that two steps removed from the cylinder.
|
|
#145
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
+1 on the build quality
|
|
#146
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
Quote:
|
|
#147
|
|||||
|
|||||
|
Quote:
+1 thanks to Bill! We also missed it but were able to throw an order together last night from McMaster . |
|
#148
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
My team is using WCP Aluminum Roller Tube - 1.25" OD x 1.125" ID x 5' Length and WCP Roller Plug - 1/2" Hex w/ 5/16-18 Threaded Hole (WCP-0102) on our robot's mechanisms. However, we are having trouble fitting the roller plug into the aluminum roller tube. We've tried filing down the roller tube and widening the hole, but we still can't get the roller plug to fit in the tube.
Does anyone have any suggestions? Any advice would be greatly appreciated. |
|
#149
|
||||
|
||||
|
Re: WCP: 2017 Product Launch + MCC 2017
Quote:
|
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|