Go to Post Haters gonna hate, Cheesers gonna cake. - Ryan Dognaux [more]
Home
Go Back   Chief Delphi > Technical > Technical Discussion
Reload this Page Getting off CMT pulleys
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
Closed Thread
 
Thread Tools Rate Thread Display Modes
  #1   Spotlight this post!  
Unread 29-01-2004, 18:52
Adam Y.'s Avatar
Adam Y. Adam Y. is offline
Adam Y.
no team (?????)
  
Join Date: Mar 2002
Location: Long Island
Posts: 1,979
Adam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to behold
Send a message via AIM to Adam Y.
Getting off CMT pulleys
Gosh darn it. I installed a CMT pulley and I did not know that it would be permamently stuck on the globe motor. Does anyone have any ideas of getting them off of the shaft?
__________________
If either a public officer or any one else saw a person attempting to cross a bridge which had been ascertained to be unsafe, and there were no time to warn him of his danger, they might seize him and turn him back without any real infringement of his liberty; for liberty consists in doing what one desires, and he does not desire to fall into the river. -Mill
Last edited by Adam Y. : 29-01-2004 at 19:04.
  #2   Spotlight this post!  
Unread 29-01-2004, 19:12
Rickertsen2 Rickertsen2 is offline
Umm Errr...
None #1139 (Chamblee Gear Grinders)
Team Role: Alumni
  
Join Date: Dec 2002
Rookie Year: 2002
Location: ATL
Posts: 1,421
Rickertsen2 has a brilliant futureRickertsen2 has a brilliant futureRickertsen2 has a brilliant futureRickertsen2 has a brilliant futureRickertsen2 has a brilliant futureRickertsen2 has a brilliant futureRickertsen2 has a brilliant futureRickertsen2 has a brilliant futureRickertsen2 has a brilliant futureRickertsen2 has a brilliant futureRickertsen2 has a brilliant future
Send a message via AIM to Rickertsen2 Send a message via Yahoo to Rickertsen2
Re: Getting off CMT pulleys
Quote:
Originally Posted by Adam Y.
Gosh darn it. I installed a CMT pulley and I did not know that it would be permamently stuck on the globe motor. Does anyone have any ideas of getting them off of the shaft?
What's a CMT pulley?
__________________
1139 Alumni
  #3   Spotlight this post!  
Unread 29-01-2004, 19:23
Adam Y.'s Avatar
Adam Y. Adam Y. is offline
Adam Y.
no team (?????)
  
Join Date: Mar 2002
Location: Long Island
Posts: 1,979
Adam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to beholdAdam Y. is a splendid one to behold
Send a message via AIM to Adam Y.
Re: Getting off CMT pulleys
They are just a pulley with a special hub that was in one of the robot kits.
__________________
If either a public officer or any one else saw a person attempting to cross a bridge which had been ascertained to be unsafe, and there were no time to warn him of his danger, they might seize him and turn him back without any real infringement of his liberty; for liberty consists in doing what one desires, and he does not desire to fall into the river. -Mill
  #4   Spotlight this post!  
Unread 29-01-2004, 21:59
Gary Bonner Gary Bonner is offline
Registered User
FRC #3974
  
Join Date: Jan 2002
Rookie Year: 2000
Location: PA
Posts: 120
Gary Bonner has a spectacular aura aboutGary Bonner has a spectacular aura about
Re: Getting off CMT pulleys
If I recall correctly, putting the set screw in the other hole releases the hub if you didn't over torque the screw in the first place.
  #5   Spotlight this post!  
Unread 30-01-2004, 07:08
Jack21 Jack21 is offline
Registered User
#0825
  
Join Date: Jan 2003
Location: Southwestern Virginia
Posts: 6
Jack21 is an unknown quantity at this point
Re: Getting off CMT pulleys
Quote:
Originally Posted by Gary Bonner
If I recall correctly, putting the set screw in the other hole releases the hub if you didn't over torque the screw in the first place.
you could try a small gear puller (common at most flea markets)
Closed Thread

« Previous Thread | Portal | Next Thread »

Thread Tools
Display Modes Rate This Thread
Hybrid Mode Hybrid Mode
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Inventor part -> 3ds max? DanL Inventor 7 12-12-2003 08:17
tool and part names angier314 Chit-Chat 0 23-04-2003 19:12
Can we use part of a container on our robot? Rick General Forum 1 10-02-2003 20:10
Can I reduce the number of similar part files? roknjohn Inventor 2 29-01-2003 21:36
team 497 needs a part Andrew Dahl General Forum 0 25-02-2002 13:22


All times are GMT -5. The time now is 02:20.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.

Contact Us - Chief Delphi - Rules - Archive - Top

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi