Rigging a PC power supply

[Tristan Lall]

Easy: just take a paperclip and connect the green wire to any black wire. The rear power switch (if so equipped) must be on. (I will assume your power supply is ATX; if it isn't, then this won't necessarily work, and won't necessarily be safe.)

Yes, I've done this. There was neither smoke, nor fire.

Here's an independent verification of my story:

First, power the thing up. You can make an ATX power supply that isn't connected to a motherboard turn on by grounding pin number 14 on the big motherboard power connector. It's easy to spot that pin, because it's the only one with a green wire going to it.

Use any handy bit of wire - like the paper clip in this picture - to connect pin 14 to any ground contact. The ground contacts are the ones with the black wires going to them. Presto, the PSU will turn on.

From dansdata.com

[mechanicalbrain]

Originally Posted by Tristan Lall

Easy: just take a paperclip and connect the green wire to any black wire. The rear power switch (if so equipped) must be on. (I will assume your power supply is ATX; if it isn't, then this won't necessarily work, and won't necessarily be safe.)

Yes, I've done this. There was neither smoke, nor fire.

Here's an independent verification of my story:
From dansdata.com

Thats perfect! Ill give it a try tomarrow and see if i can't get this working.

[sciguy125]

What I forgot to mention was how I made my switch. I got an adapter then chopped it up. There's 20-pin and 24?-pin motherboard connectors. I had a 20-pin supply, so i bought an adapter and cut the 24-pin connector off (I only needed the 20-pin). I could have just bought the connector and some pins, but they were only sold in 50-packs.

I wired up a switch between 14 and ground. The rest of the wires went to fuses for the respective outputs. There's also 3 signal pins if you want to use them. They tell you when the supply is on, plugged in, and when the power output is good (or bad, I can't remember which). You can connect LEDs to them. This gave me a nice dongle to connect to any ATX supply.

[mechanicalbrain]

Originally Posted by sciguy125

What I forgot to mention was how I made my switch. I got an adapter then chopped it up. There's 20-pin and 24?-pin motherboard connectors. I had a 20-pin supply, so i bought an adapter and cut the 24-pin connector off (I only needed the 20-pin). I could have just bought the connector and some pins, but they were only sold in 50-packs.

I wired up a switch between 14 and ground. The rest of the wires went to fuses for the respective outputs. There's also 3 signal pins if you want to use them. They tell you when the supply is on, plugged in, and when the power output is good (or bad, I can't remember which). You can connect LEDs to them. This gave me a nice dongle to connect to any ATX supply.

Sounds cool I might just do this tomorrow. I know i have all the necessary parts in my workshop.

[BrianBSL]

Another option is to use an old AT power supply - I have a couple from old PC's that have since been recycled. They require no minimum current and no pin-shorting to work. I used to use one as a basic bench supply before I got a real one.

[Dave.Norton]

Originally Posted by BrianBSL

Another option is to use an old AT power supply - I have a couple from old PC's that have since been recycled. They require no minimum current and no pin-shorting to work. I used to use one as a basic bench supply before I got a real one.

I'd be careful with an old AT supply, power supplies have gotten much better, many of those old supplies wouldn't regulate unless they were loaded, which would let the magic smoke out of anything you are working on.

[Joe Johnson]

Another thing to keep in mind when you eventually get tired of that big honking connector with just 2 shorted wires is that if you cut it off and just connect the green wire to a black one (perhaps even inside the power supply housing to keep it clean), often the supplies won't work. I found out the hard way that on some supplies you have to see which wires are joined at the connector and reconnect those wires as well.

For a PowerUp! 6100D model (cheap with loads of current capability), there are 2 orange wires and 2 black wires joined at the connector -- the power supply just will not work with out both those pairs wires joined (in addition to the grounding the green wire trick).

Good luck.

Joe J.

[mechanicalbrain]

Originally Posted by Dave.Norton

which would let the magic smoke out of anything you are working on.

Heh Ive let that magic smoke out of so many electronics that my mentor calls me smoky (I'm not joking he really does). Well it works fine. I'm going to house it in a tubaware and put in switches so i can turn off wires and not half to worry about contact. Thanks all this is perfect for a quick power source.

[Alan Anderson]

Originally Posted by mechanicalbrain

...I'm going to house it in a tubaware...

In a what?

[jdiwnab]

Originally Posted by Alan Anderson

In a what?

I think he means Tupaware, like that plastic stuff that moms with nothing to do sell in parties. It's good stuff. The Tupaware, I mean.

[sanddrag]

Originally Posted by jdiwnab

I think he means Tupaware, like that plastic stuff that moms with nothing to do sell in parties. It's good stuff. The Tupaware, I mean.

I think he means Tupperware, the plastic containers with snap/press on air tight lids for storing food.

[jdiwnab]

Originally Posted by sanddrag

I think he means Tupperware, the plastic containers with snap/press on air tight lids for storing food.

That's what I ment. I can't spell. Sorry. I think that's what "tubaware" is.

[mechanicalbrain]

Funny but i always said tubaware. Yeah if you don't have a project case or can't find one big enough use this stuff. Its amazing!