|
|
|
 Keep in mind that the lady Amanda has just taken a new job, moved herself to the NorthEast, and has to put up with people like Grady, Needel, the Kelsos, and Boucher. Let's give her some patience and sympathy. - Andy Baker [more] |
 |
|
|||||||
|
||||||||
 |
| Thread Tools | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
|
Connector for gyro chip
Does any one know where a connector for the BEI AQRS-00064-109 gyro can be found?
We are trying to use the old gyros from 2001 for programming training. |
|
#2
15-12-2005, 19:43
|
||||
|
||||
|
Re: Connector for gyro chip
ouch! I think they came in the kit of parts, and were oddball connectors.
Last time I wired up one of the old gyros I chipped the connector houseing back a little with some wire cutters, and soldered three wires right to the pins, with heatshrink over the exposed wire. |
|
#3
15-12-2005, 20:03
|
|||||
|
|||||
|
Re: Connector for gyro chip
Ooooh boy. This is exactly where we were about two weeks ago. Try to look again. I know, I know, but ours showed up right after I had given up on it. Ken's method was my last resort, though right up my alley. You know, hack slash, buy a new one, hack slash some more...
 |
|
#4
15-12-2005, 21:58
|
||||
|
||||
|
Re: Connector for gyro chip
Thanks for the replies. I emailed BEI asking where I could find the connectors and they said they no longer had them. They didn't suggest places to look.
|
|
#5
16-12-2005, 11:01
|
|||||
|
|||||
|
Re: Connector for gyro chip
Hey Im not sure if you have seen these or not but i uploaded the original spec sheets for both gyros.it includes the name and part number of the connector which is NOT made by BEI but instead is a standard part by another company. and also according to the spec sheet they are NOT or ever were included inthe KOP.
http://www.chiefdelphi.com/forums/pa...le&paperid=561 -Osc |
|
#6
16-12-2005, 15:10
|
|||||
|
|||||
|
Re: Connector for gyro chip
The connectors were included in the KOP for those years. We are still using ours.
|
|
#7
16-12-2005, 15:41
|
|||||
|
|||||
|
Re: Connector for gyro chip
Quote:
|
|
#8
16-12-2005, 20:51
|
||||
|
||||
|
Re: Connector for gyro chip
FIRST has given out two different versions of the BEI Gyro.
I could be mistaken, but I think the connector used on the older one went end-of-life (discontinued) by the manufacturer, and that is why they had to change the design of the gyro to use a different connector. |
|
#9
16-12-2005, 21:36
|
|||
|
|||
|
Re: Connector for gyro chip
You should be able to use 2 PWM cables to connect to the pins. Just check the spec sheet to see where each wire should go.
|
|
#10
16-12-2005, 22:33
|
||||||
|
||||||
|
Re: Connector for gyro chip
The connector is a Delphi-Packard connector. Since I am on leave from Delphi, I don't have the master Packard book handy any more. I think the connector is available from some sites that sell ones and twos of the Packard connectors.
Hmmm.... Let me think about it. I may be able to come up with the part number... ...stay tuned. Joe J. |
|
#11
17-12-2005, 15:16
|
|||||
|
|||||
|
Re: Connector for gyro chip
Quote:
http://www.chiefdelphi.com/forums/pa...le&paperid=561 |
|
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Optical Mouse Navigation | phrontist | Programming | 60 | 14-03-2005 21:48 |
| What RAM chip has... | MarkF | Chit-Chat | 4 | 24-03-2003 20:39 |
| chip motors next year? | JamesJones | Motors | 3 | 15-05-2002 22:38 |
| Is any team using the gyro chip? | Ragin_Kage | Kit & Additional Hardware | 4 | 10-04-2002 12:11 |
| Have YOU used the gyro chip? | FotoPlasma | Technical Discussion | 10 | 31-01-2002 13:26 |
Linear Mode
