|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
| Thread Tools | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
|
pic: How do you put an encoder on the FP Gearbox?
|
|
#2
|
|||||
|
|||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
Quote:
Since you had to cut the gearcase anyway, wouldn't it have been easier to mount a geartooth sensor near the motor pinion and just measure the electrical frequency of its signal? Or was the challenge specifically to do the job with a Vex encoder? |
|
#3
|
|||
|
|||
|
Re: pic: How do you put an encoder on the FP Gearbox?
Quote:
EDIT: Oops, I guess I didn't read the post carefully enough. Last edited by sanddrag : 06-06-2006 at 14:07. |
|
#4
|
|||||
|
|||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
Quote:
But maybe JV was asked to use a Vex encoder for some reason? |
|
#5
|
||||
|
||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
This was a "quick and dirty with what we have on hand" project.
I had plenty of Vex encoders on hand. ![]() My first idea was to attach some retro-reflective tape to the output, and use a banner sensor to count pulses. This would have been the zero-effort approach, and I think they decided it wouldn't annoy me enough, so they wouldn't let me do it. During this project I relearned to hate the FP gearbox (specifically the grease they use inside it). JV |
|
#6
|
||||||
|
||||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
Quote:
|
|
#7
|
|||
|
|||
|
Re: pic: How do you put an encoder on the FP Gearbox?
Quote:
|
|
#8
|
|||||
|
|||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
What is the accuracy? how fast can it track without going mad?
|
|
#9
|
||||
|
||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
Is that a bracket to support the shaft on the other end or is that just a collar visible on the end of the shaft?
|
|
#10
|
||||
|
||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
The great JVN does it again. Good looking piece of work there John looks promising. Very cool and exciting good luck with that. I am sure it will help FIRST in some way with the motor specs of the Fisher price motor.
-Drew |
|
#11
|
||||
|
||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
Accuracy -
It measures 1/528 revolution of the gearbox output. It can handle up to 1700 pulses/sec, but will see 1233 pulses/sec in regular usage. There is no opposite supporting bracket; that is just a shaft collar shown in the picture. JV |
|
#12
|
||||
|
||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
So, do the VEX gears mesh with that specific stage of the F-P gearbox? I haven't compared the pitches of each specific stage recently...
However, I can already envision a better use of this, which is to mechanically couple the F-P motor directly onto a existing VEX-bot. (I know the electrical add a couple more components.) Well done, shall we keep our eyes out for a whitepaper? (j/k John!) BEN |
|
#13
|
||||
|
||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
Quote:
Yes, there is a 24DP gear stage in the gearbox (or a stage that is close enough to 24DP that it meshes nicely.) It's a real short whitepaper: Cut open the gearbox, next to the 24DP gear. Mesh a vex gear with this gear. Mount stuff around it. JV |
|
#14
|
||||
|
||||
|
Re: pic: How do you put an encoder on the FP Gearbox?
Quote:
![]() |
|
#15
|
|||
|
|||
|
Re: pic: How do you put an encoder on the FP Gearbox?
How do I mount this? I'm so confused with one day left. I need to be able to stop a forklift at 4 positions. Im using a winch system with one of these motors and all I have is the gear tooth sensor (the chip thing). I know how to connect it to the RC i think, but where do I get that red thing from? and how do I connect it do the motor? please help!
|
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| how do i put the picture next to my avatar????? | call_me_Angles | CD Forum Support | 1 | 18-02-2006 10:17 |
| how to wire the new two motor gearbox | Vince lau | Electrical | 10 | 14-02-2005 07:30 |
| How to put Inventor pics on the web | Andrew Schuetze | Inventor | 7 | 05-01-2005 13:59 |
| how to add steps in the provided encoder program for the edu | Zaramel2002 | Programming | 3 | 11-02-2004 08:35 |
| How much time do you put into building your robot | Wayne Doenges | General Forum | 16 | 29-01-2002 19:30 |