PWM Frequency

[Guy_E]

All the settings were the same as if I were downloading the program using the orange cable (accept the different COM port).
As far as I know, there is no button to push in the VEX controller.
And my serial port is located on COM 1.

[Guy_E]

accept=except (what a stupid mistake)

[Mike Betts]

Originally Posted by Guy_E

accept=except (what a stupid mistake)

Guy,

Your English is quite acceptable (considering your country of origin).

I take no exception to small mistakes. ;-)

Mike

[Mike Betts]

Originally Posted by Guy_E

All the settings were the same as if I were downloading the program using the orange cable (accept the different COM port).
As far as I know, there is no button to push in the VEX controller.
And my serial port is located on COM 1.

Guy,

When you used the orange USB to RJ11 cable to program the VEX controller, you have to press the button on the cable to do it...

When the orange cable is taken apart at its DB9 connector, the program button is between the DB9 and the RJ11 connectors.

Also, insure that COM1 is set to 115K baud in the Device Manager so that it agrees with the IFI loader.

Mike

[Guy_E]

Originally Posted by Mike Betts

Guy,

When you used the orange USB to RJ11 cable to program the VEX controller, you have to press the button on the cable to do it...

When the orange cable is taken apart at its DB9 connector, the program button is between the DB9 and the RJ11 connectors.

Also, insure that COM1 is set to 115K baud in the Device Manager so that it agrees with the IFI loader.

Mike

I think you didn't understand my question. I have a cable, which has nothing to do with the VEX orange cable.

The cable is RJ11 to serial and I want to use it instead of the orange cable.
The reason I want to do it is because I have 2 VEX controllers, and only one cable and I need two (one is not mine). In order to buy a cable I need to buy the entire programming kit which costs about 100$. I want to save my money and use my own cable.

I hope Im clear now...

[Mike Betts]

Originally Posted by Guy_E

I think you didn't understand my question. I have a cable, which has nothing to do with the VEX orange cable.

The cable is RJ11 to serial and I want to use it instead of the orange cable.
The reason I want to do it is because I have 2 VEX controllers, and only one cable and I need two (one is not mine). In order to buy a cable I need to buy the entire programming kit which costs about 100$. I want to save my money and use my own cable.

I hope Im clear now...

Guy,

OK... There are three paths which you may follow...

1. Contact IFI via the VexForum and ask how to purchase the cable you want.

2. Contact IFI via the VexForum and ask for a schematic for the DB9 to RJ11 cable (with programming button) and modify your cable appropriately.

3. Take the orange cable which you already have. Using an ohm-meter, trace out each of the RJ11 pins back to the DB9 and determine which pins go where on the DB9 (at least 2 pins should connect). Then determine which pins get shorted out when the programming button is pressed (most likely the 2 unused by the DB9) and modify your cable appropriately.

Best of luck...

Mike

[Guy_E]

Thank you very much for your advices.
You have helped me alot!

[Anime-niac_2.9]

This may seem a bit off topic than what you guys are talking about, but how exactly can you program the vex controller with MPLab?

[Mike Betts]

Originally Posted by Anime-niac_2.9

This may seem a bit off topic than what you guys are talking about, but how exactly can you program the vex controller with MPLab?

Exactly the same as the FRC robots. Put another way, If you can program a FRC robot, you can program a FVC robot.

The FVC controller has exactly the same uC as the 2004 and 2005 FRC controllers. The differences due to the hardware "glue" around the uC are almost invisible to most users. In most cases, if you choose your I/O correctly, you can cut and paste your FRC code into a FVC, compile and run.

Do you have a specific question?