|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
| Thread Tools | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
|
pic: Team 8 Graber
|
|
#2
|
|||||
|
|||||
|
Re: pic: Team 8 Graber
Looks like an interesting concept.
Do you have any provisions for protecting the Globe motor in the pipeline? |
|
#3
|
|||||
|
|||||
|
Re: pic: Team 8 Graber
How do you intend to pick up a deflated tube?
|
|
#4
|
||||
|
||||
|
Re: pic: Team 8 Graber
Does it close of Just spinnings the Donut thing in?
|
|
#5
|
||||
|
||||
|
Re: pic: Team 8 Graber
|
|
#6
|
||||
|
||||
|
Re: pic: Team 8 Graber
Intresting I have a question for you are they just trying to only puy them on or are they trying to also remove the Spoilers and move them?
|
|
#7
|
||||
|
||||
|
Re: pic: Team 8 Graber
This is a reply to the posts so far.
No current thoughts about how to protect the motors. The design allows for the jaw to change sizes but this was just to figure out how the motors would function. the one at this address came first. http://www.chiefdelphi.com/forums/sh...ad.php?t=51657 Design concept allows for a possibility of taking off ringers but not exactly sure if we will be doing that or just placing ringers. |
|
#8
|
||||
|
||||
|
Re: pic: Team 8 Graber
Are you going to motorize the two outermost rollers seperately so you can rotate the tube while you're holding it?
|
|
#9
|
||||
|
||||
|
Re: pic: Team 8 Graber
OK
|
|
#10
|
|||
|
|||
|
Re: pic: Team 8 Graber
Richard: yup, thos two will be motorized individually.
Hopefuly we'll be able to also remove spoilers. Gabe: We're not sure. We might make some of it it adjustble if it seems that many tubes are deflated during regionals. -Guy |
|
#11
|
||||
|
||||
|
Re: pic: Team 8 Graber
Yeah becaue i was wondering how you guys could get spoilers off like the dsign is good on putting the keepers on but removing spoilers.... but I think it could work.
|
|
#12
|
|||
|
|||
|
Re: pic: Team 8 Graber
Hey. . .That's pipe insulation! Way to be creative!
![]() |
|
#13
|
||||
|
||||
|
Re: pic: Team 8 Graber
How well does the foam material grip the inner tube?
|
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| pic: Team 188's 2005 Student Drive Team | J Flex 188 | Extra Discussion | 6 | 10-04-2005 05:31 |
| pic: Team 1595 Final Robot Rookie TEAM L@@K!!!! | sgsdragons | Robot Showcase | 4 | 01-03-2005 16:21 |
| pic: Team 237 Robot and Team | Scott Shaw 237 | Robot Showcase | 3 | 23-02-2005 19:54 |
| pic: Team 237's wooden team buttons we handed out in Atlanta. What number did you get? | CD47-Bot | Extra Discussion | 12 | 28-07-2004 04:12 |
| pic: Team 334 Team Members after the CeBit Convention | CD47-Bot | Extra Discussion | 2 | 29-05-2004 14:14 |