|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
| Thread Tools | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
|
2006 Kit of Part Transmission
Does anybody happen to have a copy of the 2006 Kit of Parts Transmissions in cad/inventor format. If possible email the items to Pnakovich89@aol.com or post a link with a downloadable copy. Thank you for your cooperation.
|
|
#2
|
|||||
|
|||||
|
Re: 2006 Kit of Part Transmission
Not too sure which one you are referring to, the following place has a bunch of this stuff:
http://www.firstcadlibrary.com/ Jacob |
|
#3
|
||||
|
||||
|
Re: 2006 Kit of Part Transmission
its not on firstcadlibrary, and the 2006 kit of parts transmissions are the big gray metal box ones that have 2 cim motor inputs.
|
|
#4
|
|||||
|
|||||
|
Re: 2006 Kit of Part Transmission
These?
http://andymark.biz/am-0011.html If that's it, the link is near the bottom for the CAD file. It says that these were designed for FIRST... so they could be them. I've been in FIRST for 3 years now... but im a programmer Jacob |
|
#5
|
|||||
|
|||||
|
Re: 2006 Kit of Part Transmission
Quote:
|
|
#6
|
|||||
|
|||||
|
Re: 2006 Kit of Part Transmission
Quote:
|
|
#7
|
||||
|
||||
|
Re: 2006 Kit of Part Transmission
You should be receiving them in an email from me
|
|
#8
|
||||
|
||||
|
Re: 2006 Kit of Part Transmission
yup, this looks very good. Thank you, I appreciate this, i tried to make it but was unable to find the info to build the inards. this helped out alot.
|
|
#9
|
|||||
|
|||||
|
Re: 2006 Kit of Part Transmission
Here's the link to IFI's CAD model of the 2005/06 Season Kit transmissions:
http://ifirobotics.com/docs/Drivetra...rts%20STEP.zip Quote:
The AndyMark transmissions are essentially exactly the same as the IFI trannies*. The IFI transmissions however used a custom cast aluminum plate (which would be much harder to reproduce), whereas the AndyMark transmissions have two machined 3/16" aluminum plates, with a piece of square box aluminum around the outside. (You could probably eliminate this square box and just use aluminum hex/round stock as spacers if needed instead.) * The IFI transmission had a 12.755:1 ratio, where as the AndyMark has a 12.75:1 ratio. |
|
#10
|
||||
|
||||
|
Re: 2006 Kit of Part Transmission
after i downloaded these files, i tried to look at them but they were a type of 3ds max format files, are there inventor files?
|
|
#11
|
||||
|
||||
|
Re: 2006 Kit of Part Transmission
The files from AndyMark are "step" files. They will come in as blobs known as the base. You can modify them but can not edit existing features. You can add/subtract features. When you save they will be .ipt.
BTW, both AndyMark and IFI have the same ratio. |
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 2007 Kit Transmission | Brandon Holley | Rumor Mill | 1 | 06-01-2007 01:40 |
| pic: Kit Transmission Upgrade kit | Andy Baker | Extra Discussion | 17 | 29-01-2006 01:27 |
| Kit Transmission | KillerCows456 | Motors | 17 | 28-01-2006 17:10 |
| kit part exchange program | Team:1223 | Kit & Additional Hardware | 2 | 26-01-2004 10:21 |