|
|
|
 Enlighten a man who sometimes has difficulty understanding why others stray outside the box, when the box appears to be an optimized and elegant solution. - JVN [more] |
 |
|
|||||||
|
||||||||
 |
| Thread Tools | Rate Thread | Display Modes |
|
|
|
| Enlighten a man who sometimes has difficulty understanding why others stray outside the box, when the box appears to be an optimized and elegant solution. - JVN [more] |
|
|
|||||||
|
||||||||
|
| Thread Tools | Rate Thread | Display Modes |
|
#2
22-09-2007, 21:58
|
||||
|
||||
|
Re: wiring diagram
What do you really need to know about wiring the controller? The power inputs go into the 12V terminals (remember polarity!) All the PWM cables should go into the ports that your program uses. If it's default, look in the manual (I think the Left and Right drives go into ports 3 and 4 of the PWM Output terminals), Radio Cable goes into the port that says radio. I'm sorry if I'm acting like I'm treating you like a baby, but I'm not sure exactly what you are asking, so I'm stating the obvious.
|
|
#3
22-09-2007, 22:04
|
|||
|
|||
|
Re: wiring diagram
Quote:
 was there mysterious blue smoke by any chance? hehehe |
|
#4
23-09-2007, 00:27
|
||||
|
||||
|
Re: wiring diagram
If you're looking for a schematic of the RC, they dont exist.. at least not outside of the IFI staff...
|
|
#5
23-09-2007, 00:44
|
||||
|
||||
|
Re: wiring diagram
darn thats what i was looking for cause the senior fried something on the board and it might be easer to find out what he fried by knowing what exactly how the controller works. thx for ur help every one.
|
|
#6
23-09-2007, 01:03
|
|||||
|
|||||
|
Re: wiring diagram
Here is a picture of the board inside the VeX controller. I expect the IFI FRC controller looks pretty much the same, just more so. Are you sure you can fix something like this? If so, first you probably need to test it and see what is still functional and what is not, and then see about replacing the non-functioning parts. However, you might be better off sending the board in to IFI for repair....which probably will cost less than replacing the whole thing if your repair attempt goes wrong.
This might be something your team should discuss? |
|
#7
01-10-2007, 07:29
|
|||||
|
|||||
|
Re: wiring diagram
Smaug,
There is lot packed inside that little box and much of it is covered in conformal coatings. IFI is pretty good about repairs though. Customer support is one of the best things about IFI. I would check with them and get it sent back for repairs. |
|
#8
01-10-2007, 21:39
|
||||
|
||||
|
Re: wiring diagram
ok thank you every one i was hoping it might be something i could fix because it is a pretty expensive bored.
|
|
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 2005 Wiring diagram | Krazykid | Electrical | 1 | 30-01-2006 14:41 |
| Pressure Switch wiring diagram | robotjoe | Electrical | 1 | 08-02-2005 14:01 |
| Free Wiring Diagram! | Mike Alighieri | Electrical | 16 | 30-06-2003 14:31 |
| Wiring Diagram | Andrew Foster | OCCRA | 4 | 21-10-2001 19:04 |
Linear Mode
