Kit of Parts

[grsnovi]

Ali,

What computer, operating system and browser are you using? Do you have a broadband or dial-up connection?

[dtengineering]

Yes... I've seen something similar over the past couple days on firstbase, using Internet Explorer running on Vista as well as Windows 2000. When you click on the "2008" button, nothing shows up.

Fortunately most of the parts are available in the 2007 file, which is available, but it has been rather inconvenient at times when demonstrating how powerful the vitural KOP/Inventor combination is to be left without parts.

And just to further suggest that this is a problem on the website side of things... I was able to download most of the 2008 KOP from the Firstbase website last week using one of the same computers that shows nothing now.

(edit: just checked the site and it seems the 2008 KOP is back on-line... must have been a temporary glitch, but it did happen.)

(Further edit... does anyone know why the RC, Victors and Spikes aren't included under the "control system" category at firstbase? All I can find there is the backup battery. Maybe it is just assumed that everyone is using the models from www.firstcadlibrary.com.)

Jason

[keen101]

I don't know, but you can find other electronics parts modelled here:


http://www.firstcadlibrary.com/

[woods]

I went there and clicked the link on the side with the picture of the guy in the green bandana and it takes me to:

http://firstbasefrc.autodesk.com/?nd=m_kitofparts_view

Where it said:

" Autodesk Kit of Parts
Below are over 100 of the kit of parts modeled in Autodesk Inventor 2008. You can download an individual part or download a zipped file of all of the parts in that category (i.e. All of the electrical parts, all of the sensors, etc.)."

However below there is nothing.

[woods]

Ha it works!
On Firefox it didn't work, but on internet explorer it dose!

[mrmummert]

anyone know who makes the 15 tooth output sprocket? We have an old one,
but its not machined for set screws or a keyway.
Who made the 2008 Kop ones?

[ebarker]

Here are sprockets from Small Parts, Inc. They don't have 15 tooth but do have 16 tooth which will make things go a little faster. You are looking for the #35 chain, 1/2 bore. They have the set screw and keyway.

http://www.smallparts.com/products/d...tions/rcss.cfm


At MSC on page 3720
http://www1.mscdirect.com/CGI/NNPDFF?PMPAGE=3720&PARTPG=GSDRVSM&PMT4NO=36308584& PMITEM=36684397&PMCTLG=00&PMT4TP=*LTIP

there is the 36684074 part number which has a datasheet here:http://www1.mscdirect.com/CGI/NNSRIT?PMCTLG=00&PMAKA=36684074&partnerURL=http://catalogs.shoplocal.com/mscdirect/index.aspx%6Fpagename=shopmain%50circularid=11264% 50pagenumber=3716%50mode=
I think but am not sure the keyway is correct as is the setscrew.

[Mark Holschuh]

Does anyone know where I can buy the nut for the 13" lead screw? We are planning on using ours this year, but the load on it could get fairly high, especially when we get hit. It would be a good idea for us to have one or two spares. Thanks!

[mrmummert]

thank you..I'll pass this along to our lead teacher as shes the one whos gotta
order it.

[Mark Holschuh]

Originally Posted by Mark Holschuh

Does anyone know where I can buy the nut for the 13" lead screw? We are planning on using ours this year, but the load on it could get fairly high, especially when we get hit. It would be a good idea for us to have one or two spares. Thanks!

Thanks to Kevin Sevcik who posted the answer about a year ago on a similar thread. The answer is Kerk Motion at http://www.kerkmotion.com/products/l...howtoorder.asp