|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
| Thread Tools | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
|
pic: electrical panel- team 1942 Cinderella
|
|
#2
|
||||
|
||||
|
Re: pic: electrical panel- team 1942 Cinderella
Is this your competition board?
|
|
#3
|
||||
|
||||
|
Re: pic: electrical panel- team 1942 Cinderella
While it looks gorgeous, I'd hate to be the inspector who has to make sure the wiring is correct.
|
|
#4
|
|||||
|
|||||
|
Re: pic: electrical panel- team 1942 Cinderella
I'm no electrical expert but I believe the main breaker has to be connected to the distribution block and then the maxi block and breaker panels.
|
|
#5
|
||||
|
||||
|
Re: pic: electrical panel- team 1942 Cinderella
Thats why I asked if it was his competition panel. You are correct. THe main breaker must be connected the distribution block, and then all breaker panel feeds originate from the distribution block.
|
|
#6
|
|||||
|
|||||
|
Re: pic: electrical panel- team 1942 Cinderella
I agree, the Robot Electrical Distribution Diagram is the definitive picture that follows the electrical rules. Please see R50 first sentence...
"The 12V battery, the main 120-amp circuit breaker, the power distribution block, and circuit breaker distribution panels shall be connected as shown in the 2008 Power Distribution Diagram." The Main Breaker must feed the Rockwell block which in turn will feed any breaker panels you decide to use. The GDC has also rules that you may remove unused sections of the Rockwell block and cut the yellow jumpers to size as needed for your design. Actually, I like this layout. It might make it a little harder to replace a component but you have to admit it looks pretty. |
|
#7
|
||||
|
||||
|
Re: pic: electrical panel- team 1942 Cinderella
Quote:
Yes, it is a great design. No wire clutter to deal with. I was thinking the same thing, would be hard to replace a wire if you needed to. On a side note, Al, could you PM the part numbers of the pins, conncetor, and cable spool you use for making your PWM cables. Thanks. |
|
#8
|
||||
|
||||
|
Re: pic: electrical panel- team 1942 Cinderella
It looks awesome guys great job. It might bring up questions during the competition due to the fact that some of your wiring might be wired wrong. I would check up on it.
![]() |
|
#9
|
||||
|
||||
|
Re: pic: electrical panel- team 1942 Cinderella
yall shoulda used a different color. White's pretty plain.
Anyways, is the other side of the board covered? cuse if its not, then the wiring would be pretty easy to check. And if it is, i would most definitely suggest taking off the cover. It will be almost impossible to replace a part if something goes wrong. Which, since it is Virtually impossible to replace, It is Impossibly probable that something will break. |
|
#10
|
||||
|
||||
|
Re: pic: electrical panel- team 1942 Cinderella
very very very very nice
|
|
#11
|
||||
|
||||
|
Re: pic: electrical panel- team 1942 Cinderella
we closed the back side of the board- for safety ! but all the board can be removed easily, when something goes wrong!
then is not a problem to check or replace something ! ![]() |
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| pic: Team 1942- Israel Regional 2007 | aviad1942 | Extra Discussion | 2 | 20-10-2007 10:28 |
| pic: Our Electrical Panel | AndyB | Extra Discussion | 3 | 18-05-2007 08:49 |
| pic: Team 1717 Panel (alone) | rsilverstein | Extra Discussion | 13 | 28-03-2007 16:06 |
| pic: Team 1717 Panel | rsilverstein | Extra Discussion | 3 | 27-03-2007 15:55 |
| pic: Team 810's Robot - Front Panel | LetsGo810 | Extra Discussion | 2 | 30-01-2007 10:31 |