Team 25 2008 Unveiling

[IbleedPink233]

What's the drive train setup?
Obviously, 6 big (custom?) wheels. I was confused as to how many CIM's you have on the drive.
Also, I was wondering what's the top speed - I'm guessing about 10 ft/sec.

Oh yeah, awesome bot. Very impressive control over hurdling. I was also impressed by the diagonal hurdle today at Jersey.
Can't wait to see you guys in Hawaii.

[Akash Rastogi]

Originally Posted by IbleedPink233

I was also impressed by the diagonal hurdle today at Jersey.

I loved that hurdle. If i remember correctly, it bounced off another robot (us?) and then almost went out of the field. It was spectacular to watch them and 103 hurdle as well.

[Wayne C.]

Originally Posted by IbleedPink233

What's the drive train setup?
Obviously, 6 big (custom?) wheels. I was confused as to how many CIM's you have on the drive.
Also, I was wondering what's the top speed - I'm guessing about 10 ft/sec.

Oh yeah, awesome bot. Very impressive control over hurdling. I was also impressed by the diagonal hurdle today at Jersey.
Can't wait to see you guys in Hawaii.

The drive has 2 CIMS, 2 FP and the 2 Banebots motors- overall six motor drive. The hurler mechanism uses 2 CIMs with Bosch gearboxes. Our floor speed is about 10.6 FPS but we rarely got to go that fast in the traffic.

We had 2 interesting problems today = both of which we hope we have solved for tomorrow. First- the overpass is way below spec and is sagging more each round. At mid spots it is only 76 " from the floor so our plan of clipping the ball ended up with us smashing the clipper arm and needing to make repairs. We have some good ideas for tomorrow.

Our IR system was acting really strange. In the pits we got tremendous response from it- no care in the world. On the field it would cut out and act erratic. It turns out the IR lap counter emitter on the robot was right next to the system receiver and was interfering. With the power to the emitter off it worked beautifully. So we took steps to fix that for the morning too. A trial run worked just right.

So essentially all our "problems" from the day were due to factors from the field and not the robots themselves. Tomorrow will be fun.

WC

[waialua359]

Originally Posted by Wayne C.

The drive has 2 CIMS, 2 FP and the 2 Banebots motors- overall six motor drive. The hurler mechanism uses 2 CIMs with Bosch gearboxes. Our floor speed is about 10.6 FPS but we rarely got to go that fast in the traffic.

We had 2 interesting problems today = both of which we hope we have solved for tomorrow. First- the overpass is way below spec and is sagging more each round. At mid spots it is only 76 " from the floor so our plan of clipping the ball ended up with us smashing the clipper arm and needing to make repairs. We have some good ideas for tomorrow.

Our IR system was acting really strange. In the pits we got tremendous response from it- no care in the world. On the field it would cut out and act erratic. It turns out the IR lap counter emitter on the robot was right next to the system receiver and was interfering. With the power to the emitter off it worked beautifully. So we took steps to fix that for the morning too. A trial run worked just right.

So essentially all our "problems" from the day were due to factors from the field and not the robots themselves. Tomorrow will be fun.

WC

that is not good if the middle of the overpass starts or did sag. Hope other teams dont find out the same way you folks did. I saw many robots that try to clip the ball right below the overpass. I would hate to see them try to clip the overpass.
I'll be watching tomorrow. Just gotta get up at 5am.
Good luck!

[IbleedPink233]

Thanks WC for the drive info (my tower operator and I are gossiping about your bot). What kind of wheels are those?
Quote: "the overpass is way below spec and is sagging more each round. At mid spots it is only 76 " from the floor so our plan of clipping the ball ended up with us smashing the clipper arm and needing to make repairs."
- oh, so that is why I saw some people out there in between matches with a tape measurer. This is a very important observation, thanks for pointing it out for the rest of us.