Found a Source of Affordable PWM Cables ($0.65 Each!)

[MrForbes]

neat! also has 1 meter cables, if you search that sellers items for "extension" you'll see just the cables offered.

[cbale2000]

Maybe I can talk my team into getting some of these, we never seem to have any PWM cables and I constantly have to ward them off from attempting to steal them off of old robots (we try to save old bots for demonstrations).

Good find!

[Jon Jack]

Another option for teams not wanting to buy IFI's PWM cables is to make your own. They're easy to make. All you need is a special crimping tool ($40), the housings (300 for ~$60), the pins (1000 male or female pins for ~$60) and the ribbon wire (100ft for ~$35). So for ~$210 in parts and a $40 tool investment you could make 150 PWM cables at $1.40 a piece.

Yes, they are more expensive than $0.65. However, the trade off is being able to make PWM cables any size you want. This should help clean up a robots wiring.

[acdcfan259]

Originally Posted by Jon Jack

Another option for teams not wanting to buy IFI's PWM cables is to make your own. They're easy to make. All you need is a special crimping tool ($40), the housings (300 for ~$60), the pins (1000 male or female pins for ~$60) and the ribbon wire (100ft for ~$35). So for ~$210 in parts and a $40 tool investment you could make 150 PWM cables at $1.40 a piece.

Yes, they are more expensive than $0.65. However, the trade off is being able to make PWM cables any size you want. This should help clean up a robots wiring.

Assuming you treat your tools well, it's probably less because you can reuse the tool year after year.

[pogenwurst]

(Also not an ad)

While browsing DealExtreme the other day, I happened across similar offerings at similar pricing (the base cost for a given number of cables at DX is greater, but with free shipping, the final cost comes out to be on par or better -- for example, the per-cable cost of 500cm extensions is about 3 cents cheaper at DX).

http://www.dealextreme.com/details.dx/sku.11986
http://www.dealextreme.com/details.dx/sku.11987
http://www.dealextreme.com/details.dx/sku.11984

Notes:
-> one of my friends ordered some LEDs from DX, and seemed satisfied
-> from reviews, DX is legit but their shipping, while free, is apparently _slow_
-> "bulk" pricing starts at 3 or more of the same item
-> I haven't ordered any cables from DX (yet), so I can't say anything about their quality

[Dale]

Do you have recommendations on where to buy the crimping tool and related parts for making your own PWMs? I've never known exactly what those connectors were called? Having them exactly the right length would be a nice way to neaten up the control board.

[Travis Hoffman]

Originally Posted by Dale

Do you have recommendations on where to buy the crimping tool and related parts for making your own PWMs? I've never known exactly what those connectors were called? Having them exactly the right length would be a nice way to neaten up the control board.

As for alternatives to expensive PWM cables - HURRAY FOR COMPETITION!

*************

As for custom hardware and crimp tools, many recommend Hansen Hobbies and other vendors in this thread:

http://www.chiefdelphi.com/forums/sh...ight=pwm+crimp

[DonRotolo]

A very good hand crimping tool is available from Radio Shack, it's called a D-Sub crimping tool, catalog # 276-1595, listed at $10.99 at Radioshack.com.

This is the correct size for the pins sold by Mouser, for example (e.g, 538-16-02-1114 female and 538-16-02-0115 male).

[Valley Raider]

Originally Posted by Dale

Do you have recommendations on where to buy the crimping tool and related parts for making your own PWMs? I've never known exactly what those connectors were called? Having them exactly the right length would be a nice way to neaten up the control board.

I'd be careful trying to shorten them up too much. Our electronics guy did just that and every time we had to move something the cable was always too short. It was a pain. But cheap PWM are defiantly a must if you want to try and shorten them to the right length.

[Jon Jack]

Travis is right, Hansen Hobbies has the $40 crimp tool and the connectors and pins and ribbon cable I mentioned in my previous post. Mouser and Digi-Key also sell all the parts you need to make your own PWM cables, but they're more expensive than Hansen.

[pacoliketaco]

i found another site that sells cheap pwm cables:
http://www.parallax.com/Store/Access...%2cProductName
if you buy more than 10 they are $1.88 each.

[MrForbes]

that little male-male connector that is included would sure come in handy for using a vex controller/signal splitter with other stuff!

[Mark McLeod]

Originally Posted by squirrel

that little male-male connector that is included would sure come in handy for using a vex controller/signal splitter with other stuff!

I use those all the time.
Hansen and others sell them too: http://www.hansenhobbies.com/product...ors/pt1in_fma/

[pogenwurst]

Originally Posted by Mark McLeod

I use those all the time.
Hansen and others sell them too: http://www.hansenhobbies.com/product...ors/pt1in_fma/

I know they function fine regardless of what they are called ( ), but aren't those just breakaway headers?

In any case, it's a creative use of them.

Edit: I apologize in advance if this post sounds "snarky" -- it's not intended to; it's just an observation.

[MrForbes]

No, they're not breakaway headers, because the pins are long on both sides, not just one. Normal headers have short pins on the side that goes thru the board.