pic: re-modified 6wd

[Andy Baker]

Neat design

Since we are discussing the bottom plate and electronics mount... why not combine the two? You could make your plate bigger, and get rid of the polycarbonate sheet at the same time. If you make that bottom plate out of 3/32 - 1/8" thick perforated aluminum, then you have a rigid bottom plate that doubles as an electronics mount panel.

Andy

[spc295]

Originally Posted by Andy Baker

Neat design

Since we are discussing the bottom plate and electronics mount... why not combine the two? You could make your plate bigger, and get rid of the polycarbonate sheet at the same time. If you make that bottom plate out of 3/32 - 1/8" thick perforated aluminum, then you have a rigid bottom plate that doubles as an electronics mount panel.

Andy

what do you mean by perforated aluminum.

[Cory]

Originally Posted by spc295

what do you mean by perforated aluminum.

http://www.mechanicalmetals.com/perforatedmetals.html

[AdamHeard]

Originally Posted by spc295

what do you mean by perforated aluminum.

Perforated Aluminum is a sheet of aluminum with a standard pattern of holes, hexagons, squares, etc. already cut into it. Search "Perforated Aluminum" on Mcmaster; however, I would advise against buying from them as I can only see very expensive sheets available.

Another option, since it appears you have your own waterjet/sponsor with one, is to cut your own bedpan similar to how 233 does it.

[spc295]

since we cant start cutting until kickoff I will arange the electronics on 3/32 aluminum plate then mark what we can waterjet out, and then draw the plans for the bellypan.

[Jim E]

I would make the bottom plate out of 1/4"hardwood plywood. It's not only lightweight but also strong. Mounting electronics to it is a breeze too. Once you paint it, nobody can tell the difference,

[spc295]

yes but how would you mount it.

[EricH]

Flange the lower side of the inner plate, or weld on a small plate that you can put a bolt through.

Plywood is pretty strong, and the thicker versions have a lot of weight loss potential. In 2007, 330 had a very interesting pattern on the underside of its 1/2" plywood base. One of the mentors took a router to the bottom of the robot. He left a support structure for screws and bolts and took the rest down to half thickness or thinner. We had no problems that year with the base.

[sdcantrell56]

You could also do the mentioned 1/4" thick plywood or even go down to 1/8" thick and then laminate it with some fiberglass cloth and epoxy, which would make a very strong, stiff, and light board plus it would be very cheap and give you the opportunity to work with composites. Be sure to use a good plywood though like baltic birch or even better, 1088 meranti or okoume plywood.

[Tom Line]

Laminating 1/8 won't increase the stiffness that much.

You want the skins on a lamination as far apart as possible to increase rigidity. If you're going to laminate, better to buy the 1 inch thick insulation styrofoam (blue or pink). Cut out (cheese hole) the styrofoam.

Lay your glass on an old doorwall window (get it for free off craigslist or the garbage) in whatever size you need, then use epoxy to glue it to the top and bottom of your lightened styrofoam.

You'll get essentially a honeycombed panel for far less cost.

[spc295]

you guys keep mentioning flanging as a way to mount things, I dont think we have a tool available to us that would do that, (i dont think we have ever done that) what would that tool be called?

[sdcantrell56]

You would need a sheet metal break. You could probably find a local machine shop that would be able to do it for you. It would be a very quick process and if you're nice they'd probably even do it for free. You would just have to design in the extra material that will get bent out to make the flange