Go to Post Welcome to ChiefDelphi a month before Kick-Off. This is an annual traditional experience for quite a few regulars. - synth3tk [more]
Home
Go Back   Chief Delphi > Technical > Electrical
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
Closed Thread
Thread Tools Rate Thread Display Modes
  #1   Spotlight this post!  
Unread 18-04-2009, 10:51
Matt382 Matt382 is offline
Driver/Drivetrain Subteam Leader
FRC #1816 (The Green Machine)
Team Role: Driver
 
Join Date: Jun 2007
Rookie Year: 2006
Location: Minnesota
Posts: 53
Matt382 has a spectacular aura aboutMatt382 has a spectacular aura aboutMatt382 has a spectacular aura about
CompactRIO not powering up?

Our current situation is that our cRIO shuts itself off. When we first power the robot up, the lights blink and flash like they are supposed to, but a few seconds later, the lights and the cRIO itself turn off. When we check the voltage with a voltmeter, the Power Distribution Block is giving out 24 volts when not plugged into the cRIO. But when it is plugged in, the power supply is 14-15 volts.

Basically we think the problem has something to do with either a short within in the cRIO itself or the PD board. Any thoughts?
  #2   Spotlight this post!  
Unread 18-04-2009, 16:10
keehun's Avatar
keehun keehun is offline
Team Captain
AKA: Keehun Nam
FRC #2502 (EP Robotics)
Team Role: Leadership
 
Join Date: May 2008
Rookie Year: 2008
Location: Eden Priaire
Posts: 474
keehun has a reputation beyond reputekeehun has a reputation beyond reputekeehun has a reputation beyond reputekeehun has a reputation beyond reputekeehun has a reputation beyond reputekeehun has a reputation beyond reputekeehun has a reputation beyond reputekeehun has a reputation beyond reputekeehun has a reputation beyond reputekeehun has a reputation beyond reputekeehun has a reputation beyond repute
Send a message via AIM to keehun
Re: CompactRIO not powering up?

Did you try some replacement parts?
__________________
For by grace you have been saved through faith, and that not of yourselves; it is the gift of God, not of works, lest anyone should boast. -- Ephesians 2:8-9
2010: Quarter Finalist (MN 10,000 Lakes)
2010: Website Award (MN 10,000 Lakes)
2009: Quarter Finalist (MN 10,000 Lakes)
2009: GM Industrial Award (MN 10,000 Lakes)
  #3   Spotlight this post!  
Unread 18-04-2009, 18:20
Russ Beavis Russ Beavis is offline
Registered User
no team
 
Join Date: Nov 2005
Location: Manchester, NH - DEKA R&D Corp.
Posts: 341
Russ Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond repute
Re: CompactRIO not powering up?

You should confirm that your cRIO's metal chassis is isolated from the robot's frame. You may have something else touching the robot frame which is then forcing the 24V supply's ground return breaker from tripping. A simple test would be to remove the cRIO from your robot and see if it has the same problem when off the 'bot.

Russ
  #4   Spotlight this post!  
Unread 19-04-2009, 15:10
EricVanWyk EricVanWyk is offline
Registered User
no team
 
Join Date: Jan 2007
Rookie Year: 2000
Location: Boston
Posts: 1,597
EricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond reputeEricVanWyk has a reputation beyond repute
Send a message via AIM to EricVanWyk
Re: CompactRIO not powering up?

Try a different battery.

Also, measure the battery input voltage unloaded and loaded.
  #5   Spotlight this post!  
Unread 19-04-2009, 15:12
crake crake is offline
National Instruments
AKA: Chris Rake
no team (Athena)
Team Role: Engineer
 
Join Date: Apr 2008
Rookie Year: 2008
Location: Austin, TX
Posts: 185
crake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond repute
Re: CompactRIO not powering up?

Quote:
Originally Posted by Matt382 View Post
Our current situation is that our cRIO shuts itself off. When we first power the robot up, the lights blink and flash like they are supposed to, but a few seconds later, the lights and the cRIO itself turn off.
This is very strange - can you put it into safe mode and get it to boot?
  #6   Spotlight this post!  
Unread 19-04-2009, 15:45
Steigerwald's Avatar
Steigerwald Steigerwald is offline
Questionable???
FRC #0115 (MVRT)
Team Role: Mechanical
 
Join Date: Nov 2008
Rookie Year: 2006
Location: Cupertino CA
Posts: 23
Steigerwald is an unknown quantity at this point
Send a message via AIM to Steigerwald
Re: CompactRIO not powering up?

I believe you have a bad regulator inside the power distribution panel. I have seen the problem before with regulators which give lower voltage as the current demand goes up. I would check your power panel first. Possibly open it up and see if anything is blown. But before you do that, make sure to check your battery.
__________________
MVRT - Monta Vista Robotics Team #115

2009 Robot El Toro 13

2009 Davis Sacramento Regional Finalist
2009 Davis Sacramento Regional Engineering Inspiration Award
2009 Davis Sacramento Regional Best Website Award
2008 Championship Best Website Award
2008 Davis Sacramento Regional Best Website Award
2008 San Jose Best Website Award
2007 Davis Sacramento Regional Best Website Award
2006 San Jose Best Website Award
  #7   Spotlight this post!  
Unread 19-04-2009, 16:36
Matt382 Matt382 is offline
Driver/Drivetrain Subteam Leader
FRC #1816 (The Green Machine)
Team Role: Driver
 
Join Date: Jun 2007
Rookie Year: 2006
Location: Minnesota
Posts: 53
Matt382 has a spectacular aura aboutMatt382 has a spectacular aura aboutMatt382 has a spectacular aura about
Re: CompactRIO not powering up?

Thanks for the responses. We tried a few different batteries and only one of them actually worked, which seemed weird. Then we opened up the cRIO and found lots of metal shavings, which obviously should not be there. So we blew those out and put it back together and it works fine now. Now my only question is why did one of the batteries worked while the others didn't? edit: All the batteries were charged, except the one that worked was at about 10.8 volts

Last edited by Matt382 : 19-04-2009 at 16:37. Reason: battery info
  #8   Spotlight this post!  
Unread 19-04-2009, 20:51
Russ Beavis Russ Beavis is offline
Registered User
no team
 
Join Date: Nov 2005
Location: Manchester, NH - DEKA R&D Corp.
Posts: 341
Russ Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond reputeRuss Beavis has a reputation beyond repute
Re: CompactRIO not powering up?

A lead-acid battery at 10.8V without any load attached would indicate a relatively discharged battery. Even when mildly-loaded, the 12V MK battery should stay above 11V for quite a while.

As Eric VanWyk alluded to in a previous email, a discharged battery can result in the symptoms that you've described. The 24V boost converter only works down to about a 4V battery voltage. If you've got a discharged battery, the converter might work fine when the cRIO isn't attached but, upon attaching the cRIO, the supply might struggle to boost if the battery droops further to account for the extra load.

I hope that you opened the PD instead of the cRIO. Why are there metal shavings in your electronics? (insert yet another reminder to teams to please stop doing this...)

Russ
  #9   Spotlight this post!  
Unread 19-04-2009, 21:46
crake crake is offline
National Instruments
AKA: Chris Rake
no team (Athena)
Team Role: Engineer
 
Join Date: Apr 2008
Rookie Year: 2008
Location: Austin, TX
Posts: 185
crake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond repute
Re: CompactRIO not powering up?

Quote:
Originally Posted by Russ Beavis View Post
I hope that you opened the PD instead of the cRIO. Why are there metal shavings in your electronics? (insert yet another reminder to teams to please stop doing this...)
We are seeing an increase in cRIO's needing repairs due to metal shavings. It is important for teams to keep their electronics clean - as a hard bump could dislodge debris and short out something important!
  #10   Spotlight this post!  
Unread 20-04-2009, 11:12
Unsung FIRST Hero
Al Skierkiewicz Al Skierkiewicz is offline
Broadcast Eng/Chief Robot Inspector
AKA: Big Al WFFA 2005
FRC #0111 (WildStang)
Team Role: Engineer
 
Join Date: Jun 2001
Rookie Year: 1996
Location: Wheeling, IL
Posts: 10,798
Al Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond repute
Re: CompactRIO not powering up?

Matt,
Debris is not uncommon, I advised many teams to get a vacuum and attack the Crio and other electronic parts while in Atlanta. You are lucky that the severity of the short did not render your Crio permanently damaged. Erik has stated that the PD 24 volt power is protected by a 3 amp resetting circuit breaker in the PD. The fact that your 10 volt battery did not react the same way as other batteries just indicates you did not leave the Crio powered long enough for the breaker to trip. At 10.8 volts, the battery likely could not develop enough current to trip the breaker in the same time period as a fully charged battery.
__________________
Good Luck All. Learn something new, everyday!
Al
WB9UVJ
www.wildstang.org
________________________
Storming the Tower since 1996.
  #11   Spotlight this post!  
Unread 20-04-2009, 17:49
pyr0b0y pyr0b0y is offline
Programmer/Electrical
AKA: Josh
FRC #0253 (Mills Robotics Team)
Team Role: Mentor
 
Join Date: Dec 2007
Rookie Year: 2004
Location: Millbrae
Posts: 78
pyr0b0y is an unknown quantity at this point
Send a message via AIM to pyr0b0y
Re: CompactRIO not powering up?

Our team had the same problem with the metal shavings, it would shut down our cRIO everytime. No one ever thought that it would have anything to do with the metal shavings. As soon as we took care of the shavings, we did not have anymore problems....the smallest things sometimes cause the biggest problems
  #12   Spotlight this post!  
Unread 20-04-2009, 21:42
crake crake is offline
National Instruments
AKA: Chris Rake
no team (Athena)
Team Role: Engineer
 
Join Date: Apr 2008
Rookie Year: 2008
Location: Austin, TX
Posts: 185
crake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond repute
Re: CompactRIO not powering up?

Quote:
Originally Posted by pyr0b0y View Post
Our team had the same problem with the metal shavings, it would shut down our cRIO everytime. No one ever thought that it would have anything to do with the metal shavings. As soon as we took care of the shavings, we did not have anymore problems....the smallest things sometimes cause the biggest problems
Here's a little bit of insight into how metal shavings can affect the cRIO. Metal debris inside of the chassis can, at any time, cause shorts internally. You may be really lucky and short out two nets with no problem. Or, slightly less likely and short out signals that will cause errors (e.g. a data line is shorted to GND). Or, very unlucky, and the short can cause permanent damage.

In the event something unexpected occurs, and a bad instruction is executed, or a data is corrupted, the cRIO will most likely reboot (processor exception). If a power rail shorts out, depending on the location the cRIO will shut down (over-current protection), or the internal safety fuse will blow.

One nasty problem with debris is that you may not have a problem until you hit something, which could be in the middle of a match! Bad news there...

So keeping the cRIO (or any of the electronics for that matter) clean is critical, and so we're looking into documenting a procedure teams can use to maintain their hardware.
  #13   Spotlight this post!  
Unread 21-04-2009, 07:41
Unsung FIRST Hero
Al Skierkiewicz Al Skierkiewicz is offline
Broadcast Eng/Chief Robot Inspector
AKA: Big Al WFFA 2005
FRC #0111 (WildStang)
Team Role: Engineer
 
Join Date: Jun 2001
Rookie Year: 1996
Location: Wheeling, IL
Posts: 10,798
Al Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond repute
Re: CompactRIO not powering up?

Chris,
Has NI received any Crio back with metal shavings in it that caused damage? Can you post pictures or start a thread so we can hammer this point home? Metal shavings, metal flakes and metal dust from any source can be a hazard to all of the electronic components. I had a team many years ago who mounted their speed controllers next to an open frame transmission. As the gears wore themselves in, the metal flaking off, landed right in the speed controllers. One after another died from this "metal fatigue".
__________________
Good Luck All. Learn something new, everyday!
Al
WB9UVJ
www.wildstang.org
________________________
Storming the Tower since 1996.
  #14   Spotlight this post!  
Unread 21-04-2009, 11:12
crake crake is offline
National Instruments
AKA: Chris Rake
no team (Athena)
Team Role: Engineer
 
Join Date: Apr 2008
Rookie Year: 2008
Location: Austin, TX
Posts: 185
crake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond reputecrake has a reputation beyond repute
Re: CompactRIO not powering up?

Quote:
Originally Posted by Al Skierkiewicz View Post
Chris,
Has NI received any Crio back with metal shavings in it that caused damage? Can you post pictures or start a thread so we can hammer this point home? Metal shavings, metal flakes and metal dust from any source can be a hazard to all of the electronic components. I had a team many years ago who mounted their speed controllers next to an open frame transmission. As the gears wore themselves in, the metal flaking off, landed right in the speed controllers. One after another died from this "metal fatigue".
Yes, we have seen damaged controllers with metal debris inside, including one at CMP. I have some photos, but we could use some better ones for education (I'll ask RMA to get some good shots). I should also add that this year NI's RMA process was very lenient, but we should expect that in the future returns due to contamination may require charges for cleaning and repair.

Attached is one photo from CMP showing debris - inside the chassis had the same coating of plastic and metal bits.
Attached Thumbnails
Click image for larger version

Name:	517370968_jjPdN-L.jpg
Views:	51
Size:	144.6 KB
ID:	7861  

Last edited by crake : 21-04-2009 at 11:27.
  #15   Spotlight this post!  
Unread 21-04-2009, 11:29
Unsung FIRST Hero
Al Skierkiewicz Al Skierkiewicz is offline
Broadcast Eng/Chief Robot Inspector
AKA: Big Al WFFA 2005
FRC #0111 (WildStang)
Team Role: Engineer
 
Join Date: Jun 2001
Rookie Year: 1996
Location: Wheeling, IL
Posts: 10,798
Al Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond reputeAl Skierkiewicz has a reputation beyond repute
Re: CompactRIO not powering up?

Thanks Chris,
To the others viewing this picture, this is not the worst I have seen.
__________________
Good Luck All. Learn something new, everyday!
Al
WB9UVJ
www.wildstang.org
________________________
Storming the Tower since 1996.
Closed Thread


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
FRC CompactRIO firmware upgrade help mole Programming 8 17-01-2009 18:46
Buying new RC - CompactRIO Daiane General Forum 7 22-09-2008 16:03
C or LabVIEW: CompactRIO markulrich Programming 38 02-05-2008 11:21
CompactRIO - new Control System by NI ND4SPD Programming 1 17-04-2008 21:46
powering up nick_champ_2 Electrical 2 08-02-2003 15:08


All times are GMT -5. The time now is 21:01.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi