Go to Post There are no easy answers... only complicated and never ending questions. - Shawn60 [more]
Home
Go Back   Chief Delphi > ChiefDelphi.com Website > Extra Discussion
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
 
 
Thread Tools Rate Thread Display Modes
Prev Previous Post   Next Post Next
  #10   Spotlight this post!  
Unread 09-05-2009, 19:39
ShaneP's Avatar
ShaneP ShaneP is offline
Lead Mentor
FRC #0330 (The Beach Bots)
Team Role: Coach
 
Join Date: Apr 2005
Rookie Year: 2005
Location: Hermosa Beach
Posts: 158
ShaneP is a splendid one to beholdShaneP is a splendid one to beholdShaneP is a splendid one to beholdShaneP is a splendid one to beholdShaneP is a splendid one to beholdShaneP is a splendid one to beholdShaneP is a splendid one to beholdShaneP is a splendid one to behold
Re: pic: Pseudo-Swerve Close Up

Here's a response to a couple questions regarding details asked in this post.

Quote:
With the current configuration, the drive frame is rotated by a BaneBot 545 motor in a 64:1 planetary gear box which is mounted on the octagon drive frame. A rubber wheel pokes out of the frame and picks up the outer ring of the turntable which is mounted to the external frame of the robot. The octagon drive frame sits on the inner ring of the turntable. You can see the rubber wheel at the back of the robot in this photo: http://www.chiefdelphi.com/media/photos/33368

The setup is a standard 6 wheel drive setup, inside the powered turntable. Both sides are controlled separately. Since the planetary gearbox is not easily back driven, the robot drives like a normal 6 wheel drive when the 545 motor is not powered.

Alternatively, we can take off the rubber wheel and then that "frees" the 6 wheel drive (disconnecting the 545 motor with the external frame), allowing it to rotate within the external frame under it's own turning force. This is how the drive was originally designed, because it allowed the drivers to drive the robot without having to worry about handling the trailer appropriately. If the drivers wished to go straight back, they could do so by simply backing up, and the trailer would move out of the way without any effort. Essentially, you could drive straight through the trailer. However, with this configuration you cannot point the upper portion of the robot. As the robot went through design phases, the requirements for the drive changed. Once we settled on picking up off the ground and having a stationary (relative to the external frame) dumper, we needed to control the external frame, and added the motor which powered the turntable.

Although the 545 motor does create an indirect link between the trailer and drive train (thus restricting turning), this is still overcome by the driver. When the turntable is spun and the drive is rotated at the same speed in the same direction, you get virtually the same "free spin" effect, as you would without the 545 motor attached. This allows you to drive straight through the trailer again.
Throughout our season we were happy and satisfied with how the design performed on the field. Although this drive did make picking up balls off the ground more difficult (especially with the narrow-side pick up), the main benefits allowed us to win some vitally important matches. With its point-and-drive characteristics and traction control, it was a prime robot for playing defence and shutting down a high scoring opponent. Once pushing against an opponents robot, it was nearly impossible for them to get away. We could stick like glue and push them sideways around the field. If they did get away, we could cut them off during their escape (as seen in the video above).

The drive also allowed us to escape when getting pushed, so that we could go and score. We could drive the base in the direction of travel, gain speed and separate from the pushing opponent (or reduce enough force between bumpers so that the friction levels were small enough to become "unstuck"), then change direction to go free. When pinned against a wall, we could angle our driving force in which ever available direction allowed us to break free.

In several cases where the opponents trailer was close by, the base allowed us manoeuvre to it for some last second dumps.

As Eric mentioned, this drive was designed for handling the trailer and low traction surface, so it's not likely to see this drive in use again, at least for this specific purpose.

Overall we were satisfied with the drives performance, and wish we could have made it to Atlanta. We have every intent on making it to IRI, and are greatly looking forward to it.
Reply With Quote
 


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
pic: BeachBot Pseudo-Crab drive, partially assembled Joe Ross Extra Discussion 17 13-03-2009 03:03
Mounting GTS - how close is close? emmell Electrical 7 15-02-2008 00:35
pic: Differential Swerve (Close Up View) with Advanced Gear Kit nonother Extra Discussion 8 16-05-2007 01:14
Pseudo-Code dark.shadow15 Programming 6 11-11-2004 11:07
So close, but not close enough archiver 2001 1 23-06-2002 23:45


All times are GMT -5. The time now is 23:21.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi