Go to Post I can't wait to get to St. Louis!! Oh wait.. I'm already here!! - Team 288 [more]
Home
Go Back   Chief Delphi > Technical > Pneumatics
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
Closed Thread
Thread Tools Rate Thread Display Modes
  #1   Spotlight this post!  
Unread 19-01-2010, 18:26
neilpatel92's Avatar
neilpatel92 neilpatel92 is offline
Student Leader of Team 2876
AKA: Neil Patel
FRC #2876 (Devil Bots)
Team Role: Leadership
 
Join Date: Jan 2010
Rookie Year: 2009
Location: Burlington, MA
Posts: 3
neilpatel92 is an unknown quantity at this point
Send a message via Yahoo to neilpatel92
Exclamation Dangers of High Speed Pneumatic Gun

I'm looking for advice from veteran teams and mentors on pneumatics since we are a 2nd year team.

Our team was planning on using a high speed pneumatic gun to hit the soccer balls with enough velocity so they would go over the ramp.

However recently we discovered by calling Bimba that after speeds of 20 in./s on a pneumatic cylinder, the cylinder will start to break down.

We've done the physics calculations and we need the speed of the pneumatic piston to be atleast 5 m/s to use it as a gun. Obviously we need more speed for the gun design, but we don't want the gun to break down in the middle of a game either.

Is there any way that we can prevent damage on these pistons, and slow the pistons at certain points during the shot to prevent damage? Is there any way to prevent damage completely?

Or should we just scrap the idea of a pneumatic gun?

_Neil
  #2   Spotlight this post!  
Unread 19-01-2010, 20:42
EricH's Avatar
EricH EricH is offline
New year, new team
FRC #1197 (Torbots)
Team Role: Engineer
 
Join Date: Jan 2005
Rookie Year: 2003
Location: SoCal
Posts: 19,825
EricH has a reputation beyond reputeEricH has a reputation beyond reputeEricH has a reputation beyond reputeEricH has a reputation beyond reputeEricH has a reputation beyond reputeEricH has a reputation beyond reputeEricH has a reputation beyond reputeEricH has a reputation beyond reputeEricH has a reputation beyond reputeEricH has a reputation beyond reputeEricH has a reputation beyond repute
Re: Dangers of High Speed Pneumatic Gun

Quote:
Originally Posted by neilpatel92 View Post
Our team was planning on using a high speed pneumatic gun to hit the soccer balls with enough velocity so they would go over the ramp.

...

Is there any way that we can prevent damage on these pistons, and slow the pistons at certain points during the shot to prevent damage? Is there any way to prevent damage completely?

Or should we just scrap the idea of a pneumatic gun?

_Neil
Don't go fully pneumatic. Use the cylinder to swing a kicker bar.

Let r be a radius, L be a linear speed, and w be a rotational speed (technically it should be lower-case omega, but w is close).

L = r*w. Let's say that you can get a linear speed of 5 units/second out of the cylinder. You attach it close to a pivot of a kicker (let's say 5 units away from the pivot).

w is now L/r, in this case 1 radian/second.

The other end is supposed to be traveling at 20 linear units/second, let's say.

20 = r*1. You need a 20-unit long kicking device.

Do you see what I'm getting at here? Use a swinging arm and design the placement carefully, and you can get the same effect as a pneumatic cylinder going straight in at much higher speeds.
__________________
Past teams:
2003-2007: FRC0330 BeachBots
2008: FRC1135 Shmoebotics
2012: FRC4046 Schroedinger's Dragons

"Rockets are tricky..."--Elon Musk

  #3   Spotlight this post!  
Unread 19-01-2010, 20:43
Tom Line's Avatar
Tom Line Tom Line is offline
Raptors can't turn doorknobs.
FRC #1718 (The Fighting Pi)
Team Role: Mentor
 
Join Date: Jan 2007
Rookie Year: 1999
Location: Armada, Michigan
Posts: 2,554
Tom Line has a reputation beyond reputeTom Line has a reputation beyond reputeTom Line has a reputation beyond reputeTom Line has a reputation beyond reputeTom Line has a reputation beyond reputeTom Line has a reputation beyond reputeTom Line has a reputation beyond reputeTom Line has a reputation beyond reputeTom Line has a reputation beyond reputeTom Line has a reputation beyond reputeTom Line has a reputation beyond repute
Re: Dangers of High Speed Pneumatic Gun

Think along different lines. You already got your answer on how fast the cylinders can go (and here's a hint - you don't have the volume or the flow rate to get anywhere near that....).

So now you need to look at how much flow rate you DO have, how much pressure and volume you DO have, and you can turn a shorter stroke into a longer one.

Hint 1: Mechanical Advantage.
Hint 2: Think lever arm.
  #4   Spotlight this post!  
Unread 19-01-2010, 21:16
StevenB StevenB is offline
is having FRC withdrawal symptoms.
AKA: Steven Bell
no team
Team Role: College Student
 
Join Date: May 2005
Rookie Year: 2005
Location: Stanford, CA
Posts: 416
StevenB has a reputation beyond reputeStevenB has a reputation beyond reputeStevenB has a reputation beyond reputeStevenB has a reputation beyond reputeStevenB has a reputation beyond reputeStevenB has a reputation beyond reputeStevenB has a reputation beyond reputeStevenB has a reputation beyond reputeStevenB has a reputation beyond reputeStevenB has a reputation beyond reputeStevenB has a reputation beyond repute
Re: Dangers of High Speed Pneumatic Gun

Quote:
Originally Posted by Tom Line View Post
So now you need to look at how much flow rate you DO have, how much pressure and volume you DO have, and you can turn a shorter stroke into a longer one.
I'm not a mechanical engineer, but here's what I've been pondering for the last few days. Perhaps someone who really knows can confirm or refute my hypothesis.

For a given pressure, the force you get from an actuator is proportional to the area of that actuator. The speed is inversely proportional to the volume of the actuator. You can trade force for speed with a lever arm of some sort, but that is exactly what a smaller bore size does. You can quadruple your force by using a 2x larger bore size, but that reduces your speed by 4x. In short, the mechanical power of a pneumatic actuator is limited by the size of the tube and the air pressure. Both of these are dictated by the rules, as far as I understand.

If pneumatics alone can't do it, then a pure lever arm won't help. A carefully crafted kicking device might be able to do a better job than a straight pneumatic puncher, but only because it makes better use of the available power.
__________________
Need a physics refresher? Want to know if that motor is big enough for your arm? A FIRST Encounter with Physics

2005-2007: Student | Team #1519, Mechanical Mayhem | Milford, NH
2008-2011: Mentor | Team #2359, RoboLobos | Edmond, OK
2014-??: Mentor | Looking for a team...
  #5   Spotlight this post!  
Unread 19-01-2010, 22:07
MrForbes's Avatar
MrForbes MrForbes is offline
Registered User
AKA: Jim
FRC #1726 (N.E.R.D.S.)
Team Role: Mentor
 
Join Date: Feb 2006
Rookie Year: 2006
Location: Sierra Vista AZ
Posts: 6,033
MrForbes has a reputation beyond reputeMrForbes has a reputation beyond reputeMrForbes has a reputation beyond reputeMrForbes has a reputation beyond reputeMrForbes has a reputation beyond reputeMrForbes has a reputation beyond reputeMrForbes has a reputation beyond reputeMrForbes has a reputation beyond reputeMrForbes has a reputation beyond reputeMrForbes has a reputation beyond reputeMrForbes has a reputation beyond repute
Re: Dangers of High Speed Pneumatic Gun

Somewhere on my web page I have a picture of my hand with a nail in it, the result of slightly careless use of a high speed pneumatic (nail) gun.

As for kicking the ball....there are some threads on pnuematic kickers, you might want to read them

http://www.chiefdelphi.com/forums/sh...ad.php?t=80534

http://www.chiefdelphi.com/forums/sh...ad.php?t=80176

http://www.chiefdelphi.com/forums/sh...ad.php?t=80474

http://www.chiefdelphi.com/forums/sh...ad.php?t=80400
  #6   Spotlight this post!  
Unread 20-01-2010, 12:47
neilpatel92's Avatar
neilpatel92 neilpatel92 is offline
Student Leader of Team 2876
AKA: Neil Patel
FRC #2876 (Devil Bots)
Team Role: Leadership
 
Join Date: Jan 2010
Rookie Year: 2009
Location: Burlington, MA
Posts: 3
neilpatel92 is an unknown quantity at this point
Send a message via Yahoo to neilpatel92
Smile Re: Dangers of High Speed Pneumatic Gun

Thanks Everyone!

Seems like there is no way to fix this design from the replies I have gotten so I guess the idea of a high speed pneumatic gun should be thrown in the trash.

I'll keep on checking for replies but I think our team will move on to another concept; maybe, the kicker (pneumatic piston attached to lever arm) as most people here recommended.

Thanks once again,
Neil Patel
  #7   Spotlight this post!  
Unread 25-01-2010, 09:10
sparks-1784 sparks-1784 is offline
Lance Stronk
FRC #1784 (Litchbots)
Team Role: Engineer
 
Join Date: Feb 2006
Rookie Year: 2005
Location: Litchfield, CT
Posts: 46
sparks-1784 is on a distinguished road
Re: Dangers of High Speed Pneumatic Gun

A team used a pneumatic 'gun' in competition in 2008. That competition required moving something similar to a medicine ball. I don't remember the team number, but they rigged a parallel arrangement of small pneumatic cylinders (and mechanically connected in series) and used valve timing to accelerate the medicine ball. The cylinders were small to obtain higher speeds from the available flow rate. Pretty interesting design.

I would expect that something like this would work for a kicker without any mechanical advantage (read lever arm).
  #8   Spotlight this post!  
Unread 29-01-2010, 12:04
boomergeek's Avatar
boomergeek boomergeek is offline
Registered User
AKA: Mr. D (Dick DiPasquale)
FRC #0241 (Pinkerton Robotics)
Team Role: Mentor
 
Join Date: Feb 2009
Rookie Year: 2009
Location: Derry, NH
Posts: 191
boomergeek has a brilliant futureboomergeek has a brilliant futureboomergeek has a brilliant futureboomergeek has a brilliant futureboomergeek has a brilliant futureboomergeek has a brilliant futureboomergeek has a brilliant futureboomergeek has a brilliant futureboomergeek has a brilliant futureboomergeek has a brilliant futureboomergeek has a brilliant future
Re: Dangers of High Speed Pneumatic Gun

So who thinks the FIRST safety inspectors will evaluate the Bimba guideline of 20 in/second and potentially disqualify robots because of it?

I've see a lot of videos and pictures of pistons tied to kicking legs during kicking motion and I have yet to see one that seemed like the piston was traveling less than 50" per second for a long distance kick. Getting 20:1 or 30:1 foot travel versus piston travel ratio is tricky especially in robots that are only 17" tall. (I think kicking hard over long distance is on the order of 40 ft/sec.)

Disconnecting the piston stroke from a kicking motion is feasible to keep the piston under the speed limit and it could be a valuable undertaking depending on whether this "20 in/second" is going to be perceived as a safety issue.

Personally, I think I am much more concerned about designs that are storing hundreds of pound-feet of energy in unrated/unqualified elastics as that would seem to be much more dangerous than speed violations on a pneumatic piston. But then again, I'm not an actuary.

I'm only a second year guy- any wise sages out there have any suggestions?
  #9   Spotlight this post!  
Unread 29-01-2010, 12:28
Unsung FIRST Hero
Mike Betts Mike Betts is offline
Electrical Engineer
no team
Team Role: Engineer
 
Join Date: Dec 2001
Rookie Year: 1995
Location: Homosassa, FL
Posts: 1,442
Mike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond repute
Re: Dangers of High Speed Pneumatic Gun

Quote:
Originally Posted by boomergeek View Post
So who thinks the FIRST safety inspectors will evaluate the Bimba guideline of 20 in/second and potentially disqualify robots because of it?...
Dick,

The UL safety inspectors only hand out an award. The robot inspectors are the enforcement arm for this situation.

Most of us read CD regularly...

I'm going to refer you to this post I made.

Put yourself in our shoes. What would you do? Could you look yourself in the mirror if a student gets hurt?

What do you think?

Mike
__________________
Mike Betts

Alumnus, Team 3518, Panthrobots, 2011
Alumnus, Team 177, Bobcat Robotics, 1995 - 2010
LRI, Connecticut Regional, 2007-2010
LRI, WPI Regional, 2009 - 2010
RI, South Florida Regional, 2012 - 2013

As easy as 355/113...
  #10   Spotlight this post!  
Unread 29-01-2010, 12:29
Ether's Avatar
Ether Ether is offline
systems engineer (retired)
no team
 
Join Date: Nov 2009
Rookie Year: 1969
Location: US
Posts: 8,125
Ether has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond repute
Re: Dangers of High Speed Pneumatic Gun

Quote:
Originally Posted by neilpatel92 View Post
We've done the physics calculations and we need the speed of the pneumatic piston to be atleast 5 m/s to use it as a gun.
Would you be willing to share with other teams what these physics calculations were, so others can learn from them?

Thank you.


~
  #11   Spotlight this post!  
Unread 29-01-2010, 12:30
Jones571's Avatar
Jones571 Jones571 is offline
Registered User
AKA: Corey
FRC #0571 (Paragon)
Team Role: Mentor
 
Join Date: Mar 2003
Rookie Year: 2002
Location: Windsor,CT
Posts: 462
Jones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud of
Send a message via AIM to Jones571
Re: Dangers of High Speed Pneumatic Gun

Edit: Mike Betts covered it.


Al or Mike Can this even be tested at a regional and how would this be done?
__________________

Last edited by Jones571 : 29-01-2010 at 12:33.
  #12   Spotlight this post!  
Unread 29-01-2010, 12:39
Ether's Avatar
Ether Ether is offline
systems engineer (retired)
no team
 
Join Date: Nov 2009
Rookie Year: 1969
Location: US
Posts: 8,125
Ether has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond reputeEther has a reputation beyond repute
Re: Dangers of High Speed Pneumatic Gun

Quote:
IMHO it is actually rather hard to travel 20in per second we use a 4'' cylinder preloaded we would have to actuate this in quicker then 1/5 of a second...
A preloaded cylinder that is vented to atmosphere on the opposite side and that is restrained and released with a mechanical latch can easily exceed 20 ips by a large margin.

Many youtube videos clearly show speeds exceeding 20ips.


~
  #13   Spotlight this post!  
Unread 29-01-2010, 12:45
Unsung FIRST Hero
Mike Betts Mike Betts is offline
Electrical Engineer
no team
Team Role: Engineer
 
Join Date: Dec 2001
Rookie Year: 1995
Location: Homosassa, FL
Posts: 1,442
Mike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond reputeMike Betts has a reputation beyond repute
Re: Dangers of High Speed Pneumatic Gun

Quote:
Originally Posted by Jones571 View Post
... Al or Mike Can this even be tested at a regional and how would this be done?
Corey,

I have to think about it. I'm not sure that it is possible if you use a 1/8" NPT to vent...

Regards,

Mike
__________________
Mike Betts

Alumnus, Team 3518, Panthrobots, 2011
Alumnus, Team 177, Bobcat Robotics, 1995 - 2010
LRI, Connecticut Regional, 2007-2010
LRI, WPI Regional, 2009 - 2010
RI, South Florida Regional, 2012 - 2013

As easy as 355/113...
  #14   Spotlight this post!  
Unread 29-01-2010, 12:49
Jones571's Avatar
Jones571 Jones571 is offline
Registered User
AKA: Corey
FRC #0571 (Paragon)
Team Role: Mentor
 
Join Date: Mar 2003
Rookie Year: 2002
Location: Windsor,CT
Posts: 462
Jones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud ofJones571 has much to be proud of
Send a message via AIM to Jones571
Re: Dangers of High Speed Pneumatic Gun

Quote:
Originally Posted by Ether View Post

Many youtube videos clearly show speeds exceeding 20ips.


~
how exactly are you reaching this conclusion? I find it rather hard to calculate this actual IPS on youtube videos.
__________________
  #15   Spotlight this post!  
Unread 29-01-2010, 12:50
Daniel_LaFleur's Avatar
Daniel_LaFleur Daniel_LaFleur is offline
Mad Scientist
AKA: Me
FRC #2040 (DERT)
Team Role: Engineer
 
Join Date: Apr 2005
Rookie Year: 2003
Location: Peoria, IL
Posts: 1,981
Daniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond reputeDaniel_LaFleur has a reputation beyond repute
Send a message via MSN to Daniel_LaFleur
Re: Dangers of High Speed Pneumatic Gun

Quote:
Originally Posted by Mike Betts View Post
Corey,

I have to think about it. I'm not sure that it is possible if you use a 1/8" NPT to vent...

Regards,

Mike
I believe that only valves are limited by the 1/8" NPT port, not cylinders.
__________________
___________________
"We are not now that strength which in old days moved earth and heaven; that which we are, we are;
One equal temper of heroic hearts, Made weak by time and fate, but strong in will
To strive, to seek, to find, and not to yield. "
- Tennyson, Ulysses
Closed Thread


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Pneumatic Actuator Speed? WorkingFromHome Pneumatics 3 20-01-2010 00:09
High Speed 3-Fingered Hand EricVanWyk Chit-Chat 4 26-08-2009 18:25
The Dangers of Being Right (a lot) IKE Chit-Chat 14 17-06-2009 18:20
pneumatic potato gun i made vivek16 Chit-Chat 22 26-08-2007 18:49


All times are GMT -5. The time now is 22:22.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi