Camera servo

[Ziaholic]

The "thing" between buttons 8 & 9 is called the Throttle ... a.k.a Axis-3.

It goes from -1 to 1 ... but IMO, it goes the wrong way. You can wire the Axis3 (throttle) axis directly into the Tilt servo's SET POSITION. You might want to throw a "negate" in between if it acts backwards.

[umangv620]

Originally Posted by Ziaholic

The "thing" between buttons 8 & 9 is called the Throttle ... a.k.a Axis-3.

It goes from -1 to 1 ... but IMO, it goes the wrong way. You can wire the Axis3 (throttle) axis directly into the Tilt servo's SET POSITION. You might want to throw a "negate" in between if it acts backwards.

That is actually a good idea! I never knew that little thing on the front of the joystick was Axis 3.

btw(by the way), i created a post JUST like this, but I have code that does work(with the lightbulb on). I am still trying to figure out why the camera servo itself isnt working when we deploy the code.

[mcristina444]

Thanks for all the quick replies! sorry i cant take screen shots of the programming i have already done. what i basically set up was button 8 going into a case structure. (in true) i called up the Get angle then added 10 to it the put that value into Set Angle. it showed a red dot at Set angle. we deployed this code and nothing happened. is there a way to fix the red dot or should we use another Vi such as Set Position and Get position?
Also i did get the Throttle to work. all we added was a negate because it was backwards.
Again thanks for all the help. This is the second year I have been on the team and i am already the head programmer on my team.

[Alan Anderson]

Originally Posted by mcristina444

i called up the Get angle then added 10 to it the put that value into Set Angle. it showed a red dot at Set angle. we deployed this code and nothing happened. is there a way to fix the red dot or should we use another Vi such as Set Position and Get position?

The dot is because Get Angle provides an unsigned 16 bit integer, and Set Angle wants a signed 32 bit integer. They are compatible, but not identical. You are right to be concerned about it, but this particular red dot is to be expected and causes no problems.

[mcristina444]

Originally Posted by Alan Anderson

The dot is because Get Angle provides an unsigned 16 bit integer, and Set Angle wants a signed 32 bit integer. They are compatible, but not identical. You are right to be concerned about it, but this particular red dot is to be expected and causes no problems.

If there is compatibility then why isnt our robot responding? do i need to add a converter Vi in between that? or is there something else wrong with our code?

[Alan Anderson]

Originally Posted by mcristina444

If there is compatibility then why isnt our robot responding?

I don't know why your robot is not responding. You haven't given enough information about how you're trying to make it do what you want it to.

[Alan Anderson]

Originally Posted by umangv620

I am still trying to figure out why the camera servo itself isnt working when we deploy the code.

Do you have the 6v power jumper installed next to the PWM pins going to the servo?

[ecnahc515]

Originally Posted by umangv620

That is actually a good idea! I never knew that little thing on the front of the joystick was Axis 3.

btw(by the way), i created a post JUST like this, but I have code that does work(with the lightbulb on). I am still trying to figure out why the camera servo itself isnt working when we deploy the code.

Make sure you have a jumper on the pwm channel your using for the servo.

Also I have a question:

Im using axis 3 as a throttle to control the speed for our robot. Basically I wana be able to move it down to make our robots motors run slower so going over the bump isnt so fast and reckless.

I did it with controls, but I wana do this with the actual axis 3 button.

How would I go about doing it. These two are what I have:

[umangv620]

Originally Posted by ecnahc515

Make sure you have a jumper on the pwm channel your using for the servo.

That wasnt the problem. Our original code had button 2 moving the camera up and button 3 moving the camera down, and that was not moving the camera for some reason. Without touching the electrical board, we changed the camera servo code so that it moves according to the values given by Axis 3, the camera started moving. I dont know why it didnt work before, but it works now, which is one less thing for us to worry about

[umangv620]

Originally Posted by Ziaholic

The "thing" between buttons 8 & 9 is called the Throttle ... a.k.a Axis-3.

It goes from -1 to 1 ... but IMO, it goes the wrong way. You can wire the Axis3 (throttle) axis directly into the Tilt servo's SET POSITION. You might want to throw a "negate" in between if it acts backwards.

We got our camera servo working using axis 3.
to take into account the -1 to 1, the value given by the axis was divided by 4, and then added .5, so the total value would go from .25 to .75(since we dont need the camera to go up and down all the way)