|
|
|
 Let gravity be your friend. - MrForbes [more] |
 |
|
|||||||
|
||||||||
 |
| Thread Tools |
Rating: 
|
Display Modes |
|
|
|
| Let gravity be your friend. - MrForbes [more] |
|
|
|||||||
|
||||||||
|
| Thread Tools |
Rating:
|
Display Modes |
|
#16
|
||||
|
||||
|
Re: Set computer to receive it's IP via DHCP?
How do you make the bridges new ip address to be compatible with your computer.
|
|
#17
19-05-2010, 22:28
|
|||||
|
|||||
|
Re: Set computer to receive it's IP via DHCP?
If you connect and change the bridge IP to be compatible with the preferred robot setup, then after rebooting the bridge you must make your PC IP also compatible with the robot setup before you will be able to talk with the bridge again.
Assuming your PC is connected directly to the bridge... After you set the bridge IP to 10.8.42.1 you must reset the PC IP to 10.8.42.6 then you should be able to browse to the bridge again. Did you start from resetting both the bridge and router to factory defaults, or are you just resetting the bridge, since the router is probably fine already? Last edited by Mark McLeod : 19-05-2010 at 22:42.
|
|
#18
20-05-2010, 12:37
|
||||
|
||||
|
Re: Set computer to receive it's IP via DHCP?
Hey, I've now configured the bridge and the router but the bridge doesn't have a green on the driver station
Last edited by Rangel(kf7fdb) : 20-05-2010 at 13:15.
|
|
#19
20-05-2010, 13:18
|
|||||
|
|||||
|
Re: Set computer to receive it's IP via DHCP?
Go through a similar process to setup the router.
After you reset the router did you:
|
|
#20
20-05-2010, 13:21
|
|||||
|
|||||
|
Re: Set computer to receive it's IP via DHCP?
Quote:
The most likely reason for the bridge not being green is the IP address could be off (not 10.8.42.1). The green status is only if a device with that IP is found. Or your PC's IP address is not based on the same team number (10.8.42.5 for the Driver Station PC). Last edited by Mark McLeod : 20-05-2010 at 13:27.
|
|
#21
20-05-2010, 14:26
|
||||
|
||||
|
Re: Set computer to receive it's IP via DHCP?
Hey I've reset the router and the bridge, followed the steps again, and tried connecting from the classmate to the router. Then tried connecting to the bridge but still no luck. We can get into the router and into the bridge but can't connect to the bridge from the router. Anyone know what to do?
Last edited by Rangel(kf7fdb) : 20-05-2010 at 16:38.
|
|
#22
28-05-2010, 16:33
|
||||
|
||||
|
Re: Set computer to receive it's IP via DHCP?
Does anyone know how to configure a router with Firmware Version: v1.0.04. Also, is it possible to downgrade it.
|
|
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Batch files to switch between DHCP and Static IP | DtD | Programming | 9 | 28-01-2010 14:27 |
| changing code after it's set to run at startup | smcmahon | NI LabVIEW | 4 | 11-02-2009 19:36 |
| How many IR Boards did you receive? | SpaceOsc | General Forum | 3 | 22-02-2008 16:17 |
| pic: It's a bird.. It's a plane.. It's the 573 Mech Warrior bot! | Lisa Perez | Robot Showcase | 3 | 27-02-2005 15:09 |
| NJ Regional - Anyone like to receive us? | Chuck[#1156] | Regional Competitions | 27 | 03-03-2004 02:58 |
Linear Mode
