Mecanum. What's Best

[ratdude747]

that thread sounds more like the code side of the drivetrain. i think the OP was looking for the physical design of the drivetrain.

i have never built one but i have seen many others. generally, you want to run them with the wheels parallel to the main direction of travel. wide will turn better but if your manipulation design does not allow for it, don't sweat it (true for all drivetrains other than crab).

as for direct vs chain, there are pros and cons:

chain- less foolproof (thown chain= not good), but has greater flexibility of tranny and motor placement. this year chain was a good choice for mecanum (and any other wheel drives). also allows far addition gear reduction via sprocket sizes

direct- very reliable (spur gears are strong and very few teams if any use multi-speed trannies for mecanum). tranny and motor location limited to next to the wheels. depending on wheel size, stock gearing may need to be reduced to give a proper amount of torque (keep in ming mecanums have less traction so torque is less of weapon).

speaking of traction, that is another issue mecanums always seem to have- they do not have much traction compared to traction wheels. this is why teams will still use crab drive even though mecanum is just as mobile and much simpler. this is a good point to keep in mind when 2011 design time come along.

[apalrd]

Originally Posted by ratdude747

(true for all drivetrains other than crab)

Not necessarily. For a crab-drive to turn better, it requires 4-wheel independent steering and driving, with complex software and driver interfaces (the second is harder) to align each wheel with it's arc, and drive it at the correct speed.

Most teams that I have seen have independent drive motors (If they have 111-style pods, with integrated motors), and 2 steering motors. If the sides are slaved together (both lefts with 1 steering motor, both rights with 1 steering motor) you can't turn better than a skid-steer. With the front/backs slaved together, you can rotate them in either "car" (front-steer ackerman), "forklift" (rear-steer ackerman), or both, which will help but not be as optimal as 4-wheel independents steering.

[ratdude747]

exactly. what i was trying to saw was that wide drive tends to work better on all drives other than crap, since crab can be either depending on what directions the wheels are rotated at any given time. crab tends to throw a good amount of general rules out the window when it come to drivetrains.

crab is one of those things that is awesome if done right but disaster if done wrong... there was a team that shall remain anonymous that tried crab in 2006 and were forced to run it tank-style due to the programmers not having the members and time to program crab. the robot worked, but it could have been better had they opted not to try crab that year.

bottom line: crab takes a lot of effort to do right... if you are not sure if you can do it, it might be best not to.

[Dillon Carey]

Originally Posted by apalrd

Not necessarily. For a crab-drive to turn better, it requires 4-wheel independent steering and driving, with complex software and driver interfaces (the second is harder) to align each wheel with it's arc, and drive it at the correct speed.

Not necessarily. Just add two more wheels and drop the center ones and you can turn like any other skid steer bot.

[Aren_Hill]

Originally Posted by Dillon Carey

Not necessarily. Just add two more wheels and drop the center ones and you can turn like any other skid steer bot.

that also requires a degree of insanity dillon

[MrForbes]

Position the wheels so the contact with the floor makes a square. This means the robot will be a bit longer than it is wide.

We made one with 8" AM wheels, driven by AM gearboxes with a bit of reduction in the chain drive.

Suspension of some sort that lets the wheels all rest on the ground with similar weight load is helpful too, so it will drive where you want it to.

[Chris is me]

Originally Posted by apalrd

Not necessarily. For a crab-drive to turn better, it requires 4-wheel independent steering and driving, with complex software and driver interfaces (the second is harder) to align each wheel with it's arc, and drive it at the correct speed.

You can also turn a crab drive well by connecting diagonal pairs of wheels together (like 1717 did last year). This lets you both strafe and orient your wheels in a "diamond" pattern for turning on a dime.

[Jared Russell]

Originally Posted by Chris is me

You can also turn a crab drive well by connecting diagonal pairs of wheels together (like 1717 did last year). This lets you both strafe and orient your wheels in a "diamond" pattern for turning on a dime.

This configuration lets you crab and turn in place, but turning while translating is difficult.

I actually took some time last year to analyze 25 different possible steering/driving configurations for crab drives. Basically, it combined all of the typical driving and steering configurations in a giant matrix, and figured out what drive modes (crab, tank steer in both long and wide, snake/car steering) would be possible (both with and without skidding the wheels) in each. I should probably wrap it all up into a white paper when I get a chance. I looked at:

4 drive transmissions (one per wheel)
-Steered all together
-Steered in pairs (F and B, L and R, diagonal)
-Steered individually
2 drive transmissions (F and B)
-Steered all together
-Steered in pairs (F and B, L and R, diagonal)
-Steered individually
2 drive transmissions (L and R)
-Steered all together
-Steered in pairs (F and B, L and R, diagonal)
-Steered individually
2 drive transmissions (diagonal)
-Steered all together
-Steered in pairs (F and B, L and R, diagonal)
-Steered individually
1 drive transmission driving all wheels
-Steered all together
-Steered in pairs (F and B, L and R, diagonal)
-Steered individually

The only configuration that gives you perfect (no skidding necessary) crab and turning under all possible circumstances is the 4 drive transmissions/4 steering transmissions case.

[Ether]

Originally Posted by Jared341

The only configuration that gives you perfect (no skidding necessary) crab and turning under all possible circumstances is the 4 drive transmissions/4 steering transmissions case.

For the mathematically inclined, the above result is equivalent to Equation 3 which is derived in this white paper. It shows the necessary X and Y components of velocity at each wheel to achieve any desired vehicle simultaneous translational and rotational motion.

Using the results from Equation 3, the wheel angle for the nth wheel is -ATAN2(Vyn,Vxn), and the wheel rotational speed for the nth wheel is sqrt(Vxn^2+Vyn^2)/r.

[joek]

just remember, you want an X, not an O