Height of PVC pole in team version of tower

[Brandon_L]

I can't seem to find the length of the pvc pole in the team version of the tower for the minibot. Does anyone know it?

[James Tonthat]

I think you're suppose to not make it out of PVC,the real piece is 1 1/2" EMT (conduit) that you should be able to find at Home Depot or Lowes. It's 120" for reference.

[Brandon_L]

Originally Posted by James Tonthat

I think you're suppose to not make it out of PVC,the real piece is 1 1/2" EMT (conduit) that you should be able to find at Home Depot or Lowes. It's 120" for reference.

In the version for teams to build in the shop, low cost, its listed as just "Pole" so I took a guess that it was PVC as almost everything else was. Thanks!

[KevinGoneNuts]

well it would just be best for the minibot if it was the same material as what it would be in the actual competition fields. the differences in friction could be an important factor.

[CalTran]

As well as the differences in friction, the minibots are, as I found more or less implied, supposed to use magnets to stay attached to the pole. Unless you have some super pvc, I don't think the same electromagnetic field applies.

[D.Allred]

Originally Posted by Brandon_L

I can't seem to find the length of the pvc pole in the team version of the tower for the minibot. Does anyone know it?

Brandon,
The team version of the tower uses the same material as the normal competition tower. Item #3 on drawing TE-11008 references a drawing from the competition game element drawing GE-11061.

The tower pole is a 10 foot 1-1/2" Steel EMT (aka electrical conduit). There are different types of steel conduit. Make sure you get "EMT."

[GaryVoshol]

Originally Posted by CalTran

... the minibots are, as I found more or less implied, supposed to use magnets to stay attached to the pole...

That's one option that was given, not a mandate by any means.

[Brandon Holley]

Originally Posted by D.Allred

Brandon,
The team version of the tower uses the same material as the normal competition tower. Item #3 on drawing TE-11008 references a drawing from the competition game element drawing GE-11061.

The tower pole is a 10 foot 1-1/2" Steel EMT (aka electrical conduit). There are different types of steel conduit. Make sure you get "EMT."

This information is correct. The EMT conduit can be found at almost every Home Depot, Lowe's, or other various hardware stores.

-Brando

[team1512]

I am reading in several posts about a 1.5 od inch emt pole. It seems the drawings are calling for a 1.75 inch od. can anyone clarify. thanks.

[Brandon Holley]

Originally Posted by team1512

I am reading in several posts about a 1.5 od inch emt pole. It seems the drawings are calling for a 1.75 inch od. can anyone clarify. thanks.

You are looking for a 1.5" EMT pipe. The 1.5" is a pipe size that adheres to a set of regulations, but doesn't necessarily adhere to familiar fractional sizes.

Get 1.5" EMT pipe.

-Brando

[D.Allred]

Originally Posted by team1512

I am reading in several posts about a 1.5 od inch emt pole. It seems the drawings are calling for a 1.75 inch od. can anyone clarify. thanks.

1 1/2" EMT has an outside diameter of about 1 3/4". Here's a link to an EMT sizing table.

http://www.republic-conduit.com/defa...%20Conduit.pdf

[Ryan Gordon]

Originally Posted by Brandon Holley

You are looking for a 1.5" EMT pipe. The 1.5" is a pipe size that adheres to a set of regulations, but doesn't necessarily adhere to familiar fractional sizes.

Get 1.5" EMT pipe.

-Brando

To confirm if I was to measure a 1.5" EMT pipe, the O.D. would be 1.75"? (or roughly 1.75")

[waialua359]

Perhaps the updates will clarify the outside diameter.
A 1.5" EMT pole has a 1.9" OD.
As noted earlier in this post, there are references to something different. I would get clarification just to make sure.

[Brandon Holley]

Originally Posted by Ryan Gordon

To confirm if I was to measure a 1.5" EMT pipe, the O.D. would be 1.75"? (or roughly 1.75")

You are correct.

See this website: http://www.home4c.com/conduit.htm

Scroll to the bottom to view EMT sizes.

-Brando

[D.Allred]

Originally Posted by waialua359

Perhaps the updates will clarify the outside diameter.
A 1.5" EMT pole has a 1.9" OD.
As noted earlier in this post, there are references to something different. I would get clarification just to make sure.

Glenn,
You have the wrong conduit. You have "rigid" conduit, not EMT. 1 1/2" rigid conduit has a thicker wall with an OD of 1.9".