URGET RULE QUESTION: Bumper Zone

[aechmtwash11]

My team is at the St. Louis regional. We have already completed inspection and have been running practice matches today. A short time ago an inspector/referee (not sure which) told our team that our robot might be out of compliance with the 2 to 10 inch bumper zone. What happens is our drive train will raise up when we accelerate. This is an side effect of having a freely articulating drive train to converse the bump.

The question is how is this 2 to 10 inch window measured. Is it during inspection? Is it during play? Is the robot supposed to be moving?

I could see this call going either way. The total max height the bumpers get to is 13 inches, before the articulating drive hits a mechanical stop. One part of me sees the issue being a referee issue, but then again how r they going to judge it. You can't take a ruler out during a match and check. The other part of me says it should be an inspector issue since its a rule in the "robot" rules. We have been basically given the clear by the inspectors, but now they are discussing it with the field crew.

We did compete at Knoxville regional with no issue. No questions at all. Actually we got some, that's really cool. I know this doesn't mean anything, but just thought I would add that.

I know I won't get an official answer from you all, but would just like to see what the general consensus would be.

I personally, am not there yet. So all this information is coming second hand from phone calls. Any comments would be appreciated.

[Jeremy Germita]

[R29]
Bumpers must be located entirely within the Bumper Zone when the Robot is standing normally on a flat floor.

Emphasis mine.

Not sure about your situation. I just wanted to post the relevant rule. Hope it helps some. Try searching the Q&A

[EricH]

The bumper zone is measured on a flat floor, while the robot is standing normally.

If you passed inspection, you're fine. If that inspector/ref keeps bringing that up, send him to the Lead Robot Inspector to get the official ruling/the rulebook.

[slijin]

You should have a manual on hand so you can discuss the issue with the referees and clarify just which rules they think you're breaking and how. In my opinion, you're not breaking the rules (unless you're articulating the bumpers/bumper mounts themselves, in which case you are).

The relevant rules are as follows:

Originally Posted by R01-2

...the Bumper Zone, which is between 2 and 10 in. from the floor...

Originally Posted by R29

Bumpers must be located entirely within the Bumper Zone when the Robot is standing normally on a flat floor.

Originally Posted by R30

Bumpers may not be articulated.

[legogeek24]

We competed with over an inch of suspension travel and didn't have an issue. Leaving the bumper zone should only be a problem if the robot is designed to, say, tilt backwards, to the point if it were set on a flat floor the bumpers would be outside the bumper zone. Tilting during the match is alright as long as the robot will stand upright flat on the floor.

At least, that's the consensus my team came to after a very lengthy discussion. We ended up with "paradiagonal" bumpers, sloping upward from the bow to the stern as a result

[aechmtwash11]

We got a ruling from the officials (still again I don't know if it was inspectors or referees).

We are allowed to compete but if at any time the refs believe that we are using the "raised" bumpers to our advantage they will give us a technical foul. (basically to do damage to other robots, field, sabotage etc)


Reading between the lines, I think they probably have doubt with the ruling but in the spirit of FIRST are letting us compete. Something to get clarified by Q&A if we get to Championships.

Thanks for the quick responses.

[aechmtwash11]

Originally Posted by legogeek24

We ended up with "paradiagonal" bumpers, sloping upward from the bow to the stern as a result

I think this is the same thing as we have. sometimes its even slopes from starboard to port side.

[Grim Tuesday]

There is no rule that says you can't use your bumpers to your advantage. If you want to use them to get on top of the barrier, you can. Of course, anything used to damage the field is illegal, so don't use them for that. If they try to tech foul you for 'gaining advantage' from your bumpers, ask them under what rule they are giving it to you under. If they have any doubt in the legality of the bumpers, they should make you comply, not modify the rules to allow potentially illegal bumpers.

[thefro526]

The Blue Box Under R01-2 might help.

Originally Posted by R01-2 Blue Box

The carpet, the Bridge surfaces, and Keys are considered the flat floors – and thus are the reference planes for the Bumper Zone requirements. A Robot in a transitory state of crossing onto/off of a Bridge or Barrier is not considered to be on a flat floor.

Though, that doesn't cover you during acceleration. You could argue that your robot is in a transitory state but it's a little iffy.

Do you have a picture of your robot's drive train? You might be able to do something simple like add a piece of surgical tubing to one of the free floating members to make it less likely to move during stopping and starting. Done right, it shouldn't/wouldn't make a difference in your barrier crossing ability but this is design dependent.

[bduddy]

To avoid any confusion, I believe that the robot in question has a drivetrain such that it can actively change its "ride height" and thus its bumper height; it's not just suspension travel. If indeed this allows the robot to place its bumpers outside the Bumper Zone, I don't think it should be competing, but that's just me...

EDIT: I saw one or two such drivetrains at the St. Louis Regional, and I saw this team, but I'm not sure if they went together. It'd be great if the OP could describe their robot a little more completely...

[thefro526]

Originally Posted by bduddy

To avoid any confusion, I believe that the robot in question has a drivetrain such that it can actively change its "ride height" and thus its bumper height; it's not just suspension travel. If indeed this allows the robot to place its bumpers outside the Bumper Zone, I don't think it should be competing, but that's just me...

You might be right, but I interpreted this post a bit differently than you.

Originally Posted by aechmtwash11

What happens is our drive train will raise up when we accelerate. This is an side effect of having a freely articulating drive train to converse the bump.

If the drivetrain were actively articulated, a solution would be as easy as some programming to prevent unwanted articulation. But since the OP said it was freely floating, I believe that the motion is unpowered which would cause the drive to rock during starting/stopping/changing direction. If they added a slight bit of resistance to this motion (Think a simple spring to dampen it) it might be all they need to keep the bumpers legal while also retaining what sounds to be a nifty mechanism.

[Tristan Lall]

Originally Posted by aechmtwash11

What happens is our drive train will raise up when we accelerate. This is an side effect of having a freely articulating drive train to converse the bump.

Originally Posted by aechmtwash11

I think this is the same thing as we have. sometimes its even slopes from starboard to port side.

I'm glad someone finally tried this, because I've long wondered whether FIRST meant to disallow this kind of mechanism with the articulating bumper rule.

If part of your robot follows the bumper, and part of your robot follows the floor, with respect to which reference point(s) on the robot is the articulation supposed to be measured?

(Incidentally, if a connection allows motion, it's "articulated"—preventing the motion doesn't overcome that condition, at least if "articulated" is meant to be adjectival. The other interpretation of "articulated" is in the sense of the past tense of a verb. I don't know which interpretations FIRST had in mind.)

[Jaxom]

Originally Posted by Tristan Lall

I'm glad someone finally tried this, because I've long wondered whether FIRST meant to disallow this kind of mechanism with the articulating bumper rule.

If part of your robot follows the bumper, and part of your robot follows the floor, with respect to which reference point(s) on the robot is the articulation supposed to be measured?

(Incidentally, if a connection allows motion, it's "articulated"—preventing the motion doesn't overcome that condition, at least if "articulated" is meant to be adjectival. The other interpretation of "articulated" is in the sense of the past tense of a verb. I don't know which interpretations FIRST had in mind.)

I didn't look in detail at their robot (I didn't inspect it), but I don't believe their frame is articulated. That would be a violation of R01-2. Their bumpers aren't articulated; that's R30. If their drive train changes position with respect to itself is not any kind of issue; there's no rule against it.

[Tristan Lall]

Originally Posted by Jaxom

I didn't look in detail at their robot (I didn't inspect it), but I don't believe their frame is articulated. That would be a violation of R01-2. Their bumpers aren't articulated; that's R30. If their drive train changes position with respect to itself is not any kind of issue; there's no rule against it.

It's only the frame perimeter that can't be articulated. If the bumper is rigidly attached to that part of the robot, and it always satisfies the definition of a frame perimeter, I don't think there's a violation of [R01-2].

[Jaxom]

Originally Posted by Tristan Lall

It's only the frame perimeter that can't be articulated. If the bumper is rigidly attached to that part of the robot, and it always satisfies the definition of a frame perimeter, I don't think there's a violation of [R01-2].

You are correct; I was imprecise. I'm not sure how to rigidly attach a bumper (which by rule must be non-articulated) to a frame perimeter (which also, by rule, must be non-articulated) in such a way that any articulation could take place. But then, I'm not very clever.