Is this an FRC record?

[Thunderstorm]

I was just wondering if any of you know of an FRC robot that is larger than our robot this year. Since our 2015 season is done, we want to make some memorial plates commemorating our achievement and want to make sure it is a legitimate record. We measured our robot DERP today and ended up with a 31' 9" total wingspan. Here is a video of it competing at the Oklahoma Regional last weekend for those who havent seen it

#teamconveyor
#teamcrane

[bladetech932]

Look up 1987.

[Kevin Leonard]

You guys are definitely bigger than 1987, however any robot with a tether can theoretically achieve a larger length than yours is.

That being said your robot is an engineering marvel. Phenomenal job thinking outside any box whatsoever.

[Ichlieberoboter]

Nice job. Definitely bigger than 1987. Impressive engineering. What awards have you won for it?

[Thunderstorm]

Originally Posted by Ichlieberoboter

Nice job. Definitely bigger than 1987. Impressive engineering. What awards have you won for it?

We got the creativity award at the Oklahoma regional and got to talk to the president of FIRST for like 10 minutes about our robot.

[Ichlieberoboter]

Originally Posted by Thunderstorm

We got the creativity award at the Oklahoma regional and got to talk to the president of FIRST for like 10 minutes about our robot.

I figured you might have won the creativity award. Cool beans.

[CalTran]

That's pretty incredible. I like the casual reach-over-to-the-step-grab-container that you had going there. Are STEP containers the only containers that you can use, or if someone were to bring you another, could you direct the arm to grab it? Also, really clever to move the robot rather than the stack.

[MikLast]

Whoever made "Stretchy and Fetchy" in Israel looked to be similar, but i dont think it could go as far as yours.

[Thunderstorm]

Originally Posted by CalTran

That's pretty incredible. I like the casual reach-over-to-the-step-grab-container that you had going there. Are STEP containers the only containers that you can use, or if someone were to bring you another, could you direct the arm to grab it? Also, really clever to move the robot rather than the stack.

Yes, the end of our crane is actually a suction cup, we can grab containers on their side using that, however, we found that for upright containers it was easier to stick the whole suction cup inside the hole and pull it from there

[The other Gabe]

your robot is cool, and I have a question or two
why not set it up in the 60 seconds before the match instead of doing the things in auto? were you having trouble getting it down to just a minute? (it would let you canburgle in auto)

also how on earth did you get that under 120 lbs?

[orangemoore]

Originally Posted by The other Gabe

your robot is cool, and I have a question or two
why not set it up in the 60 seconds before the match instead of doing the things in auto? were you having trouble getting it down to just a minute? (it would let you canburgle in auto)

also how on earth did you get that under 120 lbs?

You cannot start in the auto zone, which they would be sitting in if they did expand before the start of the match.

[The other Gabe]

Originally Posted by orangemoore

You cannot start in the auto zone, which they would be sitting in if they did expand before the start of the match.

riiiight. oops

[Thunderstorm]

Originally Posted by The other Gabe

how on earth did you get that under 120 lbs?

Well, for starters, you'd be surprised what you have weight for when you get rid of a drive train and use no CIM motors. We could have reduced weight on the stacker but we wanted as much as we could afford in the stacker to counterbalance the crane. We also found that mangling a couple wal-mart ladders could give some decent structure on the conveyor for very low weight and the structure of the crane is almost entirely thin aluminum bent and riveted into rectangular tubes. There was alot of other stuff we wanted to add to our robot but did not have the weight for. We had a plan in the works to get the other 2 containers off the step using suction cup shooting crossbows.

[Mastonevich]

Originally Posted by Thunderstorm

you'd be surprised what you have weight for when you get rid of a drive train and use no CIM motors.

This - Nicely done, but now I have a question. How does the robot move after creating the stack if you don't have a drivetrain?

[CalTran]

Originally Posted by Thunderstorm

We had a plan in the works to get the other 2 containers off the step using suction cup shooting crossbows.