pic: Duodec-Drive (Octocanum)

[GarrettF2395]

loading photo ...

[Aren_Hill]

Garrett,

Any reason you can't put a 1/4" thick gusset plate over the corner 2x1's and just use a face mount pancake piston? Of even just nose mount the current piston. Everything would get a lot lower profile and you'd reduce your part count. (It would even be a great main frame gusset for that corner)

-Aren

[GarrettF2395]

Originally Posted by Aren_Hill

Garrett,

Any reason you can't put a 1/4" thick gusset plate over the corner 2x1's and just use a face mount pancake piston? Of even just nose mount the current piston. Everything would get a lot lower profile and you'd reduce your part count. (It would even be a great main frame gusset for that corner)

-Aren

How does that setup work with the needed rotation of the module since the cylinder wouldn't be able to pivot anymore? The change in distance isn't that much, but that still doesn't sound like the best thing for the piston.

I love the idea, I literally smacked myself on the forehead after reading your post... It made me feel foolish for not thinking of it first

[Tom Ore]

Originally Posted by GarrettF2395

How does that setup work with the needed rotation of the module since the cylinder wouldn't be able to pivot anymore? The change in distance isn't that much, but that still doesn't sound like the best thing for the piston.

We used a rigidly mounted cylinder in 2012. We positioned the cylinder to minimize the error and slotted the hole to make up the difference. Did not have any issues with it.

[Aren_Hill]

Originally Posted by GarrettF2395

How does that setup work with the needed rotation of the module since the cylinder wouldn't be able to pivot anymore? The change in distance isn't that much, but that still doesn't sound like the best thing for the piston.

I love the idea, I literally smacked myself on the forehead after reading your post... It made me feel foolish for not thinking of it first

In 2013 I did essentially this, and solved the problem by not attaching the cylinder to the module, it literally just pushed on a standoff, worked great.
(Spring pulled the module back up, reducing air consumption as well)

-Aren

[Madison]

Originally Posted by Aren_Hill

In 2013 I did essentially this, and solved the problem by not attaching the cylinder to the module, it literally just pushed on a standoff, worked great.
(Spring pulled the module back up, reducing air consumption as well)

-Aren

Our last iteration did something similar, but we pivoted the module on an axle that wasn't shared with the wheels and used the weight of the robot to lift the module up. It also made maintenance easy since we could pull the entire module without pulling any of the power transmission stuff apart.

[AdamHeard]

Originally Posted by Aren_Hill

In 2013 I did essentially this, and solved the problem by not attaching the cylinder to the module, it literally just pushed on a standoff, worked great.
(Spring pulled the module back up, reducing air consumption as well)

-Aren

We ripped Aren off and did this too.

3928's design from 2013 is so $@#$@#$@#$@# simple, that it honestly baffles me why anyone would do any variant of butterfly or octonum that isn't a copy of it.

With Andymark's new 4" mecanums, and 4" wide tube, an octonum variant is easy w/ his design.

It's so darn simple.

[dougwilliams]

Originally Posted by AdamHeard

We ripped Aren off and did this too.

3928's design from 2013 is so $@#$@#$@#$@# simple, that it honestly baffles me why anyone would do any variant of butterfly or octonum that isn't a copy of it.

With Andymark's new 4" mecanums, and 4" wide tube, an octonum variant is easy w/ his design.

It's so darn simple.

Does anyone have a picture or link to this approach?

[Madison]

Originally Posted by dougwilliams

Does anyone have a picture or link to this approach?

http://www.teamneutrino.org/seasons/...bot/butterfly/

[Nate Laverdure]

Originally Posted by Madison

http://www.teamneutrino.org/seasons/...bot/butterfly/

Doesn't show the cylinder mounting concept that Aren was talking about.

[AdamHeard]

Originally Posted by Nate Laverdure

Doesn't show the cylinder mounting concept that Aren was talking about.

In absence of finding a picture, that entire module sits inside a 3" wide tube. A 1-1/16" bore cylinder is face mounted to the top of this tube, and pushes down on the standoff above the traction wheel. there is sliding contact, and that is a nonissue.

EDIT: chassis posted here. Holes near ends on top face are where pancake cylinder mounts.

[Aren_Hill]

Uploaded it since it apparently didn't exist on CD.

The piston shown is a 1-1/16" bore pancake piston from Automation direct, 1" stroke. It pushes directly down on a 3/8" steel standoff between the two sideplates of the module, and is not connected in any other way.

The module was spring return default to traction mode by a spring (not shown) attached to the small tab you can see behind the omni.
Pop the spring off and pull a single bolt and you could pull the module out.

Any questions about it just let me know.

-Aren

[bstew]

The CAD for the module has been available for download on http://www.teamneutrino.org/seasons/...bot/butterfly/. You can see how the module works pretty well from it.

[Ryan_Todd]

Originally Posted by Aren_Hill

The piston shown is a 1-1/16" bore pancake piston from Automation direct, 1" stroke. It pushes directly down on a 3/8" steel standoff between the two sideplates of the module, and is not connected in any other way.

The module was spring return default to traction mode by a spring (not shown) attached to the small tab you can see behind the omni.
Pop the spring off and pull a single bolt and you could pull the module out.

Mind blown.

I had only ever viewed butterfly & octocanum drives as a curiosity, but now I'll have to reconsider!

[Ari423]

Originally Posted by Aren_Hill

The piston shown is a 1-1/16" bore pancake piston from Automation direct, 1" stroke. It pushes directly down on a 3/8" steel standoff between the two sideplates of the module, and is not connected in any other way.

The module was spring return default to traction mode by a spring (not shown) attached to the small tab you can see behind the omni.
Pop the spring off and pull a single bolt and you could pull the module out.

Any questions about it just let me know.

-Aren

That is an amazing design! We might be stealing this for next year