Who is missing stuff from KOP?

[ReggieB]

Our missing list:
-Spacers (see other thread)
-pneumatics kit, fitting, male run T 1/8 npt-1/4" tube. SMC
-THe pneum. kit fittings straight and elbow that are x20 seem to be 2x10, with half black plastic half white/orange
-Servo (although it looks like everyone is)
-one of the gearbox pillow block half
-need to double check on maxi block, didnt see it, but might have been looking at the wrong thing.
-the double solenoid seems to be in 2 big and 4 small pieces, is this normal?
-when they say '2' under double solenoid, do they mean the two pieces, or two solenoids?

Here are pictures of ALL of our pneu. parts, is this what other people have? Specifically the stuff on the right in the wide shot. Also, what's that other black thing, flat, about 1cmx2cm, thin, 3 holes in it?

[Sachiel7]

I think we got a bit lucky! We got TOO MUCH in our kit!
We have 2 sensor bags, our spacers are the wrong amount (too many) of each. I know we aren't missing anything big... the plug for our yellow ball. But most of its there, just some odds and ends. Oh, and I think we're missing a single solenoid.

[Ryan Albright]

we just got our kit today and we are missing alot of stuff

|Everythign to do with the robot interface
sensor bag
one of the pneumatic bags
and a bunch of loose stuff

[Arefin Bari]

we are missing a whole electrical bag, sprockets and lot more.....

[Drew Hopman]

Blue Box:
Control System accessories:
- Relay Module (spike)

missing 4

- Power Supply for Operator Interface missing 1

- Speed Controller (victor 884) missing 4

Control System Box:
- Radio Modem for Robot Controller missing 1

- Radio Modem for Operator Interface missing 1

- Robot Controller missing 1

- Operator Interface missing 1



Sensor Bag:
- Ir Beacon- victor board missing 1

- Current Sensor – Tantalem Capacitors missing 2

- Ir Beacon- Fet’s missing 2

- Ir Beacon Led’s missing 10

- Ir Beacon- resistors missing 8

- Ir Beacon – 3pin connectors missing 2

- Current Sensor missing 2

- World Beam Diffuse sensor w/screws missing 2

- Ir Beacon- photo detector (receiver) missing 5

- Current Sensor- Printed Circuit Board missing 2

Pneumatics – SMC:
- Pneumatics Kit, double solenoid base ported valve, SMC missing 2

- Pneumatics Kit, flow control, SMC missing 6

- Pneumatics Kit, fitting, straight ¼” tube, SMC missing 20

- Pneumatics Kit, fitting, 90 Elbow 1/” tube, SMC missing 20

- Pneumatics Kit, Tee Union ¼” tube, SMC missing 5

- Pneumatics Kit, Fitting, Male Run T 1/8 npt~1/4 tube SMC missing 5

- Pneumatics Kit, ¼” OD tubing, SMC missing 1

Seat/Window Bag:
- Nippon-Denso Motor, Window, Right missing 2





SEPARATE BOX:

1. Documentation Bag:

- FedEx Pouches

missing 2

- Discovering Fluid Power CDROM

missing 1



RED BOX:

1. Loose:

- Valve- Single Solenoid missing 1



I think that we were the only team that didnt recieve anything for controlls.

[Ryan Albright]

we didnt receive anyhting for controls except the joy sticks

[Robo-Knights]

Where can we purchase the :

pneumatics Kit, Fitting Male Run T 1/8 NpT 1/4 tube

Pneumatic Kit pressure switch opens @ 115psi closes @95psi :

[registered665]

yea, we at team 665 is missing two middle motor mounts. FIRST gave us two extra rear instead. go figure. we were wondering if anyone would like to trade with us.